Guyer
Geometrics for Roads and Streets - 3 PDH
This courses discusses the geometric design criteria for roads and streets. It sets forth the approaches and traffic flow criteria for guidance in determining types and configurations best suited for construction.
Preliminary Wastewater Treatment - 3 PDH
This course will introduce you to processes and equipment for preliminary treatment of wastewater. You will be introduced to descriptions, functions and design considerations for bar screens, comminuting devices, grit chambers, proportional weirs, …
Structural Design Criteria for Buildings - 3 PDH
This course introduces you to structural design criteria for the design of buildings. Included is technical guidance for buildings constructed of concrete, masonry, steel and wood. Criteria are also included for pre-engineered metal buildings, slabs on …
Geophysical Exploration Magnetic Subsurface - 9 PDH
This course provides an introduction to magnetic and subsurface methods for geophysical exploration. An overview of the spectrum of geophysical exploration methods is provided followed by more detailed discussions of magnetic and subsurface methods. …
Chemical Cleaning and Industrial Water Systems - 2 PDH
This course will introduce you to methods for cleaning industrial water systems with chemicals. You will learn about pre-operational cleaning which is performed to prepare water-contacted metal surfaces to receive chemical treatment to provide protection …
Tropical Engineering Concrete, Wood, Metals - 3 PDH
This course provides an introduction to the application of concrete, wood and metal materials and products in construction for tropical climates where humidity, weather and seafront locations are considerations. Concrete materials, reinforcement, …
Impressed Current Cathodic - 3 PDH
This course provides an introduction to impressed current cathodic protection systems. There are two principle methods of providing cathodic protection: sacrificial anode and impressed current. The primary advantage of impressed current cathodic …
Geotextiles in Pavement and Drainage Applications - 2 PDH
This course will introduce you to geotextiles made from polypropylene, polyester, polyethylene, polyamide (nylon), polyvinylidene chloride, and fiberglass. You will learn about their physical properties, functions, and design methods. You will also learn …
Foundations In Areas of Significant Frost Penetration - 3 PDH
Areas of significant frost penetration may be defined as those in which freezing temperatures occur in the ground to sufficient depth to be a significant factor in foundation design. These areas may be further characterized as seasonal frost and …
Area Drainage Systems - 5 PDH
This course will introduce you to normal requirements for design of surface and subsurface drainage systems for residential, commercial, institutional and industrial areas.
Soil Grouting - 3 PDH
Grouting is a widely used method for strengthening and sealing rock, soil and concrete. The possibilities for sealing structures are of great importance from both an economic and environmental point of view. The cost of grouting has in certain projects …
Asphalt Concrete Pavement Recycling - 3 PDH
This publication contains guidance for preparing plans and specifications and for ensuring the quality of recycled bituminous concrete. In addition, this publication provides useful information to design engineers, laboratory personnel, and inspectors …
Water Systems Pumps and Drivers - 3 PDH
This course covers the operation of pumps used in water supply systems. It also covers the motors, engines, and accessories (together called pump drivers) that provide the mechanical source of energy to pumps. Velocity pumps and positive-displacement …
Architectural Design: Golf Clubhouses - 3 PDH
This course will introduce you to the fundamentals of golf clubhouse design. You will learn about the fundamentals of site and building design, functional area criteria, space allocations and illustrative designs for small, medium and large clubhouses. …
Incinerator Emissions and Permitting - 3 PDH
This course describes and quantifies whenever possible the air pollution particulate emissions which are the direct result of the incineration process. The incineration process consists of burning solid, semisolid, liquid, or gaseous waste to produce …
Cathodic Concepts - 3 PDH
This course provides the basic concepts of cathodic protection, together with important criteria and precautions to be observed. Corrosion of metals is a result of electrochemical reactions. An electrochemical reaction is a chemical reaction accompanied …
Rock Mass Characterization - 3 PDH
This course provides guidance in the description and engineering classification of intact rock and rock masses, the types, applications and analyses of rock property tests, the evaluation of intact rock and rock mass properties, and the selection of …
Primary Wastewater Treatment - 3 PDH
Wastewater treatment is usually characterized as consisting of four sequential processes: preliminary, primary, secondary and tertiary treatment. This course will introduce you to processes and equipment for primary treatment of wastewater. You will be …
Bearing Capacity Analysis - 3 PDH
This course will introduce you to methods for analysis of soils and rock to determine load bearing capacity. Stresses transmitted by a foundation to underlying soils must not cause bearing-capacity failure or excessive foundation settlement. The design …
Steel Bridge Maintenance - 3 PDH
This course discusses steel bridge maintenance and repair. Preventive maintenance of steel bridge components consists mainly of measures to protect the steel from corrosion. When deicing salt is added to the electrolyte, there is a dramatic increase in …
High Temperature Water Heating Plants - 5 PDH
This course will introduce you to systems, equipment and design guidelines for high temperature water (HTW) heating plants. HTW systems are used for heating multi-building facilities such as campuses and industrial and commercial activities. The advantage …
Tropical Engineering: Mechanical, Electrical, Miscellaneous - 3 PDH
This course provides an introduction to special considerations in design of plumbing, HVAC, electrical distribution and miscellaneous features and systems in tropical climates where high humidity, heat, heavy rain and seafront conditions are common.
Makeup Water Industrial Water - 3 PDH
This course provides an introduction to makeup water for Industrial water systems. Many installations use fresh water and, often, potable water. Makeup water, often referred to as “makeup,” is fresh water that is added to an industrial water system to …
How To Become Registered as an Architectural Engineer - 3 PDH
Engineers who have passed the Fundamentals of Engineering (FE) registration examination (formerly called the Engineer-in-Training….EIT exam) or both the FE and the Principles and Practices of Engineering (PE) registration examination in another discipline …
Pavement Design in Seasonal Frost Conditions - 5 PDH
This publication presents criteria and procedures for the design and construction of pavements placed on subgrade or base course materials subject to seasonal frost action. The most prevalent modes of distress in pavements and their causes are listed. The …
Levees Seepage Slope Settlement - 3 PDH
This course will introduce you to methods for controlling seepage and settlement in the construction of levees, and to generally acceptable guidelines for levee slopes. Without control, underseepage in pervious foundations beneath levees may result in (a) …
Soil Stabilization for Pavements - 3 PDH
This course will introduce you to accepted methods for stabilizing soils underlying new pavements to improve strength and durability. You will also learn about methods to achieve better soil gradation, and reduction of plasticity index or swelling …
Drainage Pipe Strength, Cover, and Bedding - 3 PDH
This course provides an introduction to drainage pipe strength, cover and bedding. A drainage pipe is defined as a structure (other than a bridge) to convey water through a trench or under a fill or some other obstruction. Materials for permanent-type …
Area Development Plans - 3 PDH
Area Development Planning PDH provides an introduction to the Area Development Planning (ADP) process that is commonly used in developing new project sites. The planning procedures described are a guide that can be modified to suit specific project …
Central Heating Plant Planning - 3 PDH
This publication contains data and information as criteria to guide the planning of steam and high temperature water (HTW) central and individual heating plants. Engineering and economic considerations are identified to guide siting decisions, fuel …
Cathodic Protection Inspection Testing - 5 PDH
This discussion includes criteria and inspection actions that, when used either separately or in combination, will indicate whether adequate cathodic protection of a metallic piping system has been achieved. The effectiveness of cathodic protection or …
Hydroelectric Power Plant Structures - 3 PDH
The course discusses location, configuration and design considerations for hydroelectric powerhouses. The factors affecting the location include: Location of the spillway (when powerhouse is located adjacent to the dam). Location of navigation locks (on …
Rigid Pavement Design - 3 PDH
This is an introduction to rigid pavement design. It is a basic treatment that will introduce designers to some important principles and terminology. In simple applications on real projects the information provided will give designers a good start in …
Concrete Pavements - 7 PDH
This course provides information on the materials and construction procedures for portland cement concrete pavements. It describes the constituents to be used in concrete, the procedures to be used in manufacturing concrete, and the equipment and …
Bridge Sub-Superstructure Inspection - 3 PDH
This is an introduction to the factors to consider in inspection of bridge superstructures and substructures. This course will help you to address a variety of bridge maintenance issues.
Treated Water Storage - 4 PDH
This course provides an introduction to design criteria for treated water storage requirements at facilities, gives typical design analyses for elevated tanks, standpipes, and reservoirs, and provides guidance on the procedures to be followed in selecting …
Water Supply Systems Operation and Maintenance - 3 PDH
This publication provides an introduction to maintenance inspections and general maintenance services required at domestic water supply systems. It contains information about tools and equipment, lubricants, and materials and supplies required to perform …
Marine Fueling Facilities - 3 PDH
This course provides an introduction to the design of marine applications of petroleum fueling facilities. Design of marine fuel receiving and dispensing facilities for the purpose of receiving fuel and/or loading fuel aboard ships, barges and boats for …
Hydraulic Design of Sewers - 3 PDH
This course will introduce you to the principles of hydraulic design of sanitary sewers. You will learn how to calculate quantities of wastewater, the approach to design of gravity and depressed sewers, required pumping capacity, hydrogen sulfide gas …
Retaining Walls And Excavation Support Systems - 3 PDH
Retaining walls must be designed so that foundation pressures do not exceed allowable bearing pressures, wall settlements are tolerable, safety factors against sliding and overturning are adequate, and the wall possesses adequate structural strength. …
Dam Arch Construction - 3 PDH
This course will introduce you to the construction of concrete arch dams. The design and analysis of any dam assumes that the construction will provide a suitable foundation and uniform quality of concrete. The design also depends on the construction to …
Soils: Identification and Classification - 4 PDH
This course will introduce you to the principles and practices of identification and classification of soil and rock. Identification and classification are the essential first steps in soil mechanics and engineering, and engineering of foundations for …
Recycling Construction and Demolition Waste - 3 PDH
There is a significant amount of construction and demolition (C&D) waste developed due to construction activities and structure demolition, for example, at some installations, construction and demolition waste accounts for up to 80 percent of the solid …
Building Design Specifications and Tools - 3 PDH
This course will introduce you to the most important resource available to engineers and architects engaged in the design of buildings and related infrastructure. It represents the collective knowledge of thousands of engineers and architects acquired …
Deep Foundations - 3 PDH
This course will provide you with an introduction to deep foundations. A deep foundation derives its support from competent strata at significant depths below the surface or, alternatively, has a depth to diameter ratio greater than 4. A deep foundation …
Cathodic Protection Maintenance - 3 PDH
This course will provide you with an introduction to the methods, equipment and practices for inspection and maintenance of cathodic protection systems. Both galvanic (sacrificial anode) and impressed current systems are discussed.
Carbon Adsorption for Waste Treatment - 3 PDH
This course discusses waste treatment using, primarily, activated carbon. Both liquid and vapor phase adsorption are discussed. Adsorption technologies may be applicable to treatment of both sanitary and industrial waste streams.
Sanitary Landfills - 3 PDH
This is an introduction to the planning and design of sanitary landfills. You will learn about dry and wet landfills, site selection, site development plans, site layout, trench design, leachate control and treatment, gas control, runoff control, support …