Civil Engineering
OSHA: Construction, Demolition & Cleanup Safety Issues - 6 PDH
Construction, demolition, and cleanup projects are inherently hazardous. Accident rates in these industries are accordingly higher than in other industries. OSHA’s mission is to reduce these accident rates through safety rules and regulations. This course …
Methods for Cleaning Contaminated Soils - 4 PDH
EPA uses many methods to clean up pollution at Superfund and other sites. This course presents various EPA-approved methods for cleaning contaminated soils. For each method, the course describes 1) how the method works, 2) how safe it is, 3) how long it …
OSHA: Fatalities from Improper Work Practices - 4 PDH
This course is based on case studies taken from the Occupational Safety and Health Administration’s “Fatal Facts” —descriptions of accidents in which one or more workers died because of improper work practices. Reading and thinking about these case …
FHWA Bridge Inspection Fundamentals - 6 PDH
The Federal Highway Administration’s Bridge Inspector’s Reference Manual (BIRM) is a comprehensive manual on programs, procedures, and techniques for inspecting and evaluating a variety of in-service highway bridges. BIRM serves as the basis of a …
FHWA Bridge Inspection Reporting - 5 PDH
The Federal Highway Administration’s Bridge Inspector’s Reference Manual (BIRM) is a comprehensive manual on programs, procedures, and techniques for inspecting and evaluating a variety of in-service highway bridges. BIRM serves as the basis of a …
Asbestos Standard for the Construction Industry - 5 PDH
In the construction industry, asbestos is found in installed products such as sprayed-on fireproofing, pipe insulation, floor tiles, cement pipe and sheet, roofing felts and shingles, ceiling tiles, fire-resistant drywall, drywall joint compounds, and …
Building in Coastal Areas - 5 PDH
The design and construction of residential buildings in coastal zones presents problems not usually found in more inland locations. For example, all elements of the building must be able to withstand the large forces associated with high wind speeds and …
Seepage and Drainage - 7 PDH
This course covers surface erosion, and analysis of flow quantity and groundwater pressures associated with underseepage. Requirements are given for methods of drainage and pressure relief. Control of soil erosion must be considered in all new …
Sacrificial Anode Cathodic - 3 PDH
This course will provide you with an introduction to the methods, equipment and practices for design and operation of sacrificial anode cathodic protection systems.
Small Flow Waste Treatment Systems - 3 PDH
This course will introduce you to small flow waste treatment systems such as septic tanks, waterless toilets, filtration and reuse systems, Imhoff tanks, and packaged treatment plants. You will learn about subsurface absorption and how to conduct …
Domestic Wastewater Treatment - 3 PDH
This course will introduce you to the basics of domestic wastewater treatment. You will learn about preliminary measures, pretreatment, primary, secondary and advanced treatment processes, and sludge treatment and disposal. Approximate performance data …
Stormwater Drainage and Site Development - 3 PDH
This publication provides an introduction to stormwater drainage systems and improvements for land development projects, and strategies and considerations in site development.
Waste Treatment Carbon Adsorption Applications - 3 PDH
This course discusses waste treatment using, primarily, activated carbon. Both liquid and vapor phase adsorption are discussed. Adsorption technologies may be applicable to treatment of both sanitary and industrial waste streams.
High Temperature Water Heating Plants - 5 PDH
This course will introduce you to systems, equipment and design guidelines for high temperature water (HTW) heating plants. HTW systems are used for heating multi-building facilities such as campuses and industrial and commercial activities. The advantage …
Cathodic Protection Principles - 5 PDH
This course will provide you with an introduction to the principles of cathodic protection for underground and underwater structures. You will be introduced to the physics and chemistry of the corrosion process and how to mitigate the corrosion using …
Primary Wastewater Treatment - 3 PDH
Wastewater treatment is usually characterized as consisting of four sequential processes: preliminary, primary, secondary and tertiary treatment. This course will introduce you to processes and equipment for primary treatment of wastewater. You will be …
Architectural Design: Golf Clubhouses - 3 PDH
This course will introduce you to the fundamentals of golf clubhouse design. You will learn about the fundamentals of site and building design, functional area criteria, space allocations and illustrative designs for small, medium and large clubhouses. …
Design of Solar Water Heating Systems - 3 PDH
This course presents the information required to design a solar energy water heating system, after planning and system selection have been completed.
Roller-Compacted Concrete Pavements - 3 PDH
Procedures and criteria described here are applicable to the design and construction of roller-compacted concrete (RCC) pavement (RCCP). Roller-compacted concrete pavement employs a concrete paving technology that involves laydown and compaction of a …
Dam Arch Manual Design Layout - 3 PDH
This course will introduce you to a methodology for manual layout of concrete arch dams. In practice layout of concrete arch dams is, of course, a computerized process, but understanding an approach to manual layout will be an excellent way to gain an …
Water Desalination - 5 PDH
This course will introduce you to water desalination technologies, processes and methods. You will learn the importance of site and water source selection. You will be introduced to an approach for selecting the appropriate desalination technology and …
Water System Pumps Operation and Maintenance - 3 PDH
This course covers the operation and maintenance of pumps used in water supply and treatment facilities. It also covers the motors, engines, and accessories (together called pump drivers) that provide the mechanical source of energy to pumps.
Industrial Makeup Water - 3 PDH
This course discusses makeup water for industrial water systems. Industrial water systems usually use fresh water and, often, potable water. Makeup water, often referred to as “makeup,” is fresh water that is added to an industrial water system to replace …
Hydraulic Design of Culverts - 3 PDH
This course will introduce you to a nomographic approach to hydraulic design of culverts. Culverts are hydraulic structures intended to convey, generally, stormwater and other unanticipated flows in and around earth and other structures such as highways, …
Settlement and Volume Expansion in Soils -5 PDH
This course concerns (a) immediate settlements, (b) long-term settlements, (c) rate of settlement, (d) criteria for tolerable settlement, (e) methods of reducing or accelerating settlements for saturated fine-grained soils and (f) methods for controlling …
Security Fences - 3 PDH
This course applies to all construction, renovation, and repair projects including temporary construction that includes security fencing and gates. Security fences and gates are installed and used primarily to define the perimeter of protected areas, such …
Soil Grouting - 3 PDH
Grouting is a widely used method for strengthening and sealing rock, soil and concrete. The possibilities for sealing structures are of great importance from both an economic and environmental point of view. The cost of grouting has in certain projects …
Trickling Filter Wastewater Treatment Plants - 3 PDH
This course provides an introduction to trickling filter wastewater treatment plants. Trickling filter plants have been justified by their low initial cost, low operating and maintenance costs, and relative simplicity of operation. Although the effluent …
Situ Treatment of Hazardous Soil - 3PDH
This discussion course discussions methods and technologies for treatment of contaminated soil in situ (without substantive excavation of the soil).
Constructing Maintaining Cathodic Protection - 3 PDH
This course will provide you with an introduction to the principles of cathodic protection for underground and underwater structures. You will be introduced to the physics and chemistry of the corrosion process and how to mitigate the corrosion using …
Rigid Pavement Design - 3 PDH
This is an introduction to rigid pavement design. It is a basic treatment that will introduce designers to some important principles and terminology. In simple applications on real projects the information provided will give designers a good start in …
Area Development Plans - 3 PDH
Area Development Planning PDH provides an introduction to the Area Development Planning (ADP) process that is commonly used in developing new project sites. The planning procedures described are a guide that can be modified to suit specific project …
Earthwork for Foundations - 3 PDH
This course provides an introduction to earthwork for foundations. In general, excavation for subsurface structures will consist of open excavation and shaft and tunnel excavation. Where excavation to great depths is required, a variety of soils and rock …
Slope Stability Analysis - 3 PDH
This course is concerned with characteristics and critical aspects of the stability of excavation slopes; methods of designing slopes, including field observations and experience, slope stability charts, and detailed analyses; factors of safety; and …
Dam Arch Foundation Investigation - 3 PDH
Foundation investigations for arch dams generally must be accomplished in more exacting detail than for other dam types because of the critical relationship of the dam to its foundation and to its abutments. This course discusses the procedures which are …
Water Treatment - 5 PDH
This course will provide an introduction to water treatment processes and technology. You will be introduced to factors to consider in selecting water treatment processes, preliminary treatment, aeration, coagulation and flocculation, sedimentation …
Geotextiles in Pavement and Drainage Applications - 2 PDH
This course will introduce you to geotextiles made from polypropylene, polyester, polyethylene, polyamide (nylon), polyvinylidene chloride, and fiberglass. You will learn about their physical properties, functions, and design methods. You will also learn …
Air Quality Boiler Plants - 5 PDH
This publication provides an introduction to air quality control and monitoring equipment for fuel fired plants such as steam boiler plants. Included are discussions of chemical, cooling and sump pumps, nitrogen and carbon dioxide systems, ash handling, …
Soil Stabilization Construction Procedures - 3 PDH
This is an introduction to the factors to consider in inspecting and repairing steel bridges. This course will help you to address a variety of bridge inspection situations that may be encountered. This course provides an introduction to construction …
Incinerator Emissions and Permitting - 3 PDH
This course describes and quantifies whenever possible the air pollution particulate emissions which are the direct result of the incineration process. The incineration process consists of burning solid, semisolid, liquid, or gaseous waste to produce …
Steam Generators - 3 PDH
This course addresses the design requirements for gas, oil, coal, and waste fuel fired steam generating, water-tube boilers and components with steam capacities between 20,000 and 250,000 pph and maximum pressures of 450 pounds per inch gauge …
Hot Mix Asphalt Pavement - 5 PDH
This course will tell you about hot-mix asphalt often used for high-performance pavements. The degree of performance required should be selected based on traffic conditions and the availability of satisfactory materials.
Soil Stabilization for Pavements - 3 PDH
This course will introduce you to accepted methods for stabilizing soils underlying new pavements to improve strength and durability. You will also learn about methods to achieve better soil gradation, and reduction of plasticity index or swelling …
Engineering Properties of Soil and Rock - 5 PDH
This course will introduce you to the engineering properties of soil and rock. You will learn how the properties of compaction, permeability, consolidation-swell, shear strength, stress-strain modulus (modulus of elasticity), and Poisson’s ratio are …
Tropical Engineering: Building Envelope - 3 PDH
This publication provides an introduction to design of building envelopes in tropical climates where heat and humidity are important considerations. Discussed are roofing, wall materials, windows, doors, finishes and miscellaneous specialties.
Foundations on Fill and Backfilling - 3 PDH
Foundations may be constructed on fills and backfilled material. Fills may include conventional compacted fills; hydraulic fills; and uncontrolled fills of soils or industrial and domestic wastes, such as ashes, slag, chemical wastes, building rubble, and …
Gas Distribution - 3 PDH
This course contains instructions and engineering information relating to gas distribution pipe systems, including pressure regulators, valves, meters, and other necessary appurtenances, for the distribution of fuel gas, natural and manufactured, from the …
Sanitary Landfills - 3 PDH
This is an introduction to the planning and design of sanitary landfills. You will learn about dry and wet landfills, site selection, site development plans, site layout, trench design, leachate control and treatment, gas control, runoff control, support …