Guyer
400 Hz Electrical - 3 PDH
This course includes information necessary for the proper design of 400-Hertz (Hz) conversion, distribution, and utilization systems. Special regard is paid to systems utilizing medium-voltage distribution. Systems supplying 400 Hz for ground-power …
Activated Sludge Wastewater Treatment Plants - 3 PDH
This course provides an introduction to activated sludge wastewater treatment plants. In a conventional (plug-flow) activated sludge plant, the primary-treated wastewater and acclimated micro-organisms (activated sludge or biomass) are aerated in a basin …
Adsorption Technologies Operation Theory- 3 PDH
This course discusses practical guidance for the design of liquid and vapor phase devices for the adsorption of organic chemicals. The adsorptive media addressed include granular activated carbon (GAC) and other alternative adsorption carbon media, such …
Advanced Wastewater Treatment - 5 PDH
This course will introduce you to advanced wastewater treatment processes that provide higher quality wastewater discharge than achievable with primary and secondary treatment alone. You will learn innovative sewage handling techniques such as polishing …
Air Quality Boiler Plants - 5 PDH
This publication provides an introduction to air quality control and monitoring equipment for fuel fired plants such as steam boiler plants. Included are discussions of chemical, cooling and sump pumps, nitrogen and carbon dioxide systems, ash handling, …
Air Traffic Control Facilities - 3 PDH
This publication provides an introduction to the planning and design of air traffic control facilities, such as would be required at airports and airfields. Building-types discussed are the Terminal Radar Approach Control Facility, Area Control and …
An Engineer’s Guide to Influencing Public Policy - 3 PDH
Engineers often are called upon to interact with public policy makers in the course of their careers, their professional development, and in pursuit of personal interests. There are, however, fundamental differences in what motivates engineers and what …
Architectural Design: Fire Stations - 3 PDH
This course will introduce you to the principles of architectural planning and design. Because architectural design is largely a subjective process, the “casebook” approach is used to illustrate it. In this instance, the architectural design of fire …
Architectural Design: Golf Clubhouses - 3 PDH
This course will introduce you to the fundamentals of golf clubhouse design. You will learn about the fundamentals of site and building design, functional area criteria, space allocations and illustrative designs for small, medium and large clubhouses. …
Architectural Design: Libraries - 3 PDH
Architectural Design: Libraries PDH will introduce you to the principles of architectural planning and design. Because architectural design is largely a subjective process, the "casebook" approach is used to illustrate it. In this instance, the …
Architectural Theatres Vol. 3 - 3 PDH
This publication provides an introduction to certain aspects of the architectural design of theatres and concert halls. This volume discusses access, environmental systems, and performance support spaces.. Topics discussed include audience access, …
Architectural Theatres Vol. 4 - 3 PDH
This publication provides an introduction to certain aspects of the architectural design of theatres and concert halls. This volume discusses theatre lighting, scenery and soft goods, and rigging and stage mechanisms. Topics discussed include audience …
Area Development Plans - 3 PDH
Area Development Planning PDH provides an introduction to the Area Development Planning (ADP) process that is commonly used in developing new project sites. The planning procedures described are a guide that can be modified to suit specific project …
Area Drainage Systems - 5 PDH
This course will introduce you to normal requirements for design of surface and subsurface drainage systems for residential, commercial, institutional and industrial areas.
Asphalt Concrete Pavement Recycling - 3 PDH
This publication contains guidance for preparing plans and specifications and for ensuring the quality of recycled bituminous concrete. In addition, this publication provides useful information to design engineers, laboratory personnel, and inspectors …
Auxiliary Power Systems Switchboard - 3 PDH
This publication provides technical guidance and design requirements for operation and maintenance of auxiliary electric power systems.
Auxiliary Systems Operation & Maintenance - 3 PDH
This publication provides technical guidance and design requirements for operation and maintenance of auxiliary electric power systems.
Bearing Capacity Analysis - 3 PDH
This course will introduce you to methods for analysis of soils and rock to determine load bearing capacity. Stresses transmitted by a foundation to underlying soils must not cause bearing-capacity failure or excessive foundation settlement. The design …
Boiler Control Systems: An Introduction - 4 PDH
This course provides an introduction to criteria for the design of heating plant instrumentation. A heating plant may contain one or more boilers. The plant may be an individual plant serving a single building or a compact group of buildings, or a …
Boiler Inspections - 3 PDH
This course provides guidance for the inspection of steam and hot water boilers and unfired pressure vessels. In addition to boilers, inspection and testing is discussed for carbon dioxide and liquid petroleum gas vessels, heat exchangers, and deaerators.
Building Design Specifications and Tools - 3 PDH
This course will introduce you to the most important resource available to engineers and architects engaged in the design of buildings and related infrastructure. It represents the collective knowledge of thousands of engineers and architects acquired …
Bulk Fuel Storage - 5 PDH
This course provides guidance for the design of bulk fuel storage facilities, including bulk storage tanks and those components normally located within a typical bulk storage compound. These components include pipeline receiving facilities, tank truck and …
Carbon Adsorption for Waste Treatment - 3 PDH
This course discusses waste treatment using, primarily, activated carbon. Both liquid and vapor phase adsorption are discussed. Adsorption technologies may be applicable to treatment of both sanitary and industrial waste streams.
Cathodic Concepts - 3 PDH
This course provides the basic concepts of cathodic protection, together with important criteria and precautions to be observed. Corrosion of metals is a result of electrochemical reactions. An electrochemical reaction is a chemical reaction accompanied …
Cathodic Protection for Underground Structures - 5 PDH
This is an introduction to cathodic protection for underground structures such as tanks and pipelines. It covers the two principal methods used to mitigate corrosion: the sacrificial anode and impressed current systems. It introduces you to the nine …
Cathodic Protection Inspection Testing - 5 PDH
This discussion includes criteria and inspection actions that, when used either separately or in combination, will indicate whether adequate cathodic protection of a metallic piping system has been achieved. The effectiveness of cathodic protection or …
Cathodic Protection Maintenance - 3 PDH
This course will provide you with an introduction to the methods, equipment and practices for inspection and maintenance of cathodic protection systems. Both galvanic (sacrificial anode) and impressed current systems are discussed.
Cathodic Protection Principles - 5 PDH
This course will provide you with an introduction to the principles of cathodic protection for underground and underwater structures. You will be introduced to the physics and chemistry of the corrosion process and how to mitigate the corrosion using …
Central Heating Plant Planning - 3 PDH
This publication contains data and information as criteria to guide the planning of steam and high temperature water (HTW) central and individual heating plants. Engineering and economic considerations are identified to guide siting decisions, fuel …
Chemical Cleaning and Industrial Water Systems - 2 PDH
This course will introduce you to methods for cleaning industrial water systems with chemicals. You will learn about pre-operational cleaning which is performed to prepare water-contacted metal surfaces to receive chemical treatment to provide protection …
Coatings and Paints - 5 PDH
Painting and coating of surfaces in buildings and other infrastructure construction require careful attention to specification, application and inspection if construction materials are to be effectively protected for a substantial service life. This …
Communication Systems for Medical Facilities - 4 PDH
This course will introduce you to communication systems for medical facilities, including hospitals, medical clinics, and medical and laboratories. You will learn about communication distribution facilities, telephone system requirements, …
Concrete Pavements - 7 PDH
This course provides information on the materials and construction procedures for portland cement concrete pavements. It describes the constituents to be used in concrete, the procedures to be used in manufacturing concrete, and the equipment and …
Constructing Maintaining Cathodic Protection - 3 PDH
This course will provide you with an introduction to the principles of cathodic protection for underground and underwater structures. You will be introduced to the physics and chemistry of the corrosion process and how to mitigate the corrosion using …
Cooling Tower Water Treatment - 3 PDH
Cooling water systems remove heat generated from a variety of industrial processes. There are three basic types of cooling water systems: once-through, open recirculating, and closed recirculating cooling water systems. This publication describes water …
Dam Arch Foundation Investigation - 3 PDH
Foundation investigations for arch dams generally must be accomplished in more exacting detail than for other dam types because of the critical relationship of the dam to its foundation and to its abutments. This course discusses the procedures which are …
Dam Arch Manual Design Layout - 3 PDH
This course will introduce you to a methodology for manual layout of concrete arch dams. In practice layout of concrete arch dams is, of course, a computerized process, but understanding an approach to manual layout will be an excellent way to gain an …
Deep Foundations - 3 PDH
This course will provide you with an introduction to deep foundations. A deep foundation derives its support from competent strata at significant depths below the surface or, alternatively, has a depth to diameter ratio greater than 4. A deep foundation …
Design of Dewatering Systems - 3 PDH
This course discusses design of a watering and pressure relief or groundwater control system. To do this first requires determination of the type of groundwater flow (artesian, gravity, or combined) to be expected and of the type of system that will be …
Design of Industrial Ventilation Systems - 3 PDH
This course is an introduction to the design of industrial ventilation systems. You will be introduced to general design criteria, controls, operational considerations and commissioning. You will also be provided with a more detailed discussion of two of …
Design of Solar Water Heating Systems - 3 PDH
This course presents the information required to design a solar energy water heating system, after planning and system selection have been completed.
Distribution of Stresses in Soil - 3 PDH
This course covers the analysis of stress conditions at a point, stresses beneath structures and embankments, and empirical methods for estimating loads on buried pipes, conduits, shafts, and tunnels.
Domestic Wastewater Treatment - 3 PDH
This course will introduce you to the basics of domestic wastewater treatment. You will learn about preliminary measures, pretreatment, primary, secondary and advanced treatment processes, and sludge treatment and disposal. Approximate performance data …
Drainage Pipe Strength, Cover, and Bedding - 3 PDH
This course provides an introduction to drainage pipe strength, cover and bedding. A drainage pipe is defined as a structure (other than a bridge) to convey water through a trench or under a fill or some other obstruction. Materials for permanent-type …
Earthwork for Foundations - 3 PDH
This course provides an introduction to earthwork for foundations. In general, excavation for subsurface structures will consist of open excavation and shaft and tunnel excavation. Where excavation to great depths is required, a variety of soils and rock …
Electric Power Requirements for Buildings - 3 PDH
This course will introduce you to an approach you can use to determine electric power requirements for buildings and multi-building developments and activities. You will learn about terminology, and acquisition and analysis of preliminary load data you …
Electrical Safety Aerial - 3 PDH
This course includes specific requirements for poles and structures, pole-mounted equipment, and aerial lines. Requirements addressed include pole handling and erection, climbing and working on poles, stringing of lines, working around pole-mounted …
Electrical Safety Substations - 3 PDH
This course provides an introduction to electrical safety when working around substations and switchgear. A substation provides a protected area for switching power circuits and may include transforming power from one voltage to another. For the purposes …
Electrical Safety Underground - 3 PDH
This course provides electrical safety guidance when working with underground electrical systems and low voltage interior systems. It applies to underground work in manholes, vaults, and handholes; work on duct lines, trenches, and underground cables; …
Electrical Systems for Medical Facilities - 5 PDH
This course will introduce you to electrical systems for medical facilities, including hospitals, medical and dental clinics, and medical and dental laboratories. You will learn about general electrical requirements, exterior electrical systems, alternate …
Energy Efficient HVAC Controls - 3 PDH
This course covers automatic temperature and humidity controls, space pressurization controls, safety controls, and energy monitoring and central supervisory control systems for heating, ventilating and air conditioning (HVAC) systems. The control system …
Engineering Properties of Soil and Rock - 5 PDH
This course will introduce you to the engineering properties of soil and rock. You will learn how the properties of compaction, permeability, consolidation-swell, shear strength, stress-strain modulus (modulus of elasticity), and Poisson’s ratio are …
Ethical Issues from the Kansas City Hyatt Hotel Collapse - 3 PDH
This course will examine the ethical issues that arose from the 1981 collapse of atrium lobby walkways at the newly constructed Hyatt Regency Hotel in Kansas City, Missouri. This tragic incident resulted in the loss of 114 lives and 200 injuries and is …
Ethical Issues from the St. Francis Dam Failure - 3 PDH
This course will examine the ethical issues that arose from the 1928 failure of the St. Francis Dam near Los Angeles, California. Near midnight on March 12 of that year the 195-feet high concrete arch dam collapsed catastrophically, releasing 12 billion …
Ethical Issues in Design-Build - 3 PDH
The widespread growth of “design-build” presents ethical issues for engineers and architects. If these issues are not addressed it is likely public reaction to abuses the process invites will result in the loss of design-build as a construction delivery …
Ethical Issues: The Tacoma Narrows Bridge Collapse - 3 PDH
This course will examine the ethical issues that arose from the 1940 collapse of the Tacoma Narrows bridge in Washington state. This was one of the most dramatic bridge collapses in history, with fortunately no loss of life and little property damage …
Field Explorations for Foundations - 3 PDH
Field explorations of existing soil and rock conditions are essential before undertaking design of foundations for buildings and structures. This course introduces you to investigational programs for surface examination including documentary evidence, …
Fire Protection Engineering for Buildings - 3 PDH
This course will introduce you to fire protection engineering fundamentals related to building materials and design, water supply for fire protection, fire extinguishing systems, fire alarm systems, special occupancies and hazards, and storage of …
Fire Suppression ITM - 3 PDH
This course will introduce you to best practices for inspection, testing and maintenance of fire detection, alarm and suppression systems to assure reliable and effective operation in emergency situations. You will be introduced to the principles of …
Flexible Pavement Design - 3 PDH
This is an introduction to flexible pavement design. It is a basic treatment that will introduce designers to some important principles and terminology. In simple applications on real projects the information provided will give designers a good start in …
Foundations In Areas of Significant Frost Penetration - 3 PDH
Areas of significant frost penetration may be defined as those in which freezing temperatures occur in the ground to sufficient depth to be a significant factor in foundation design. These areas may be further characterized as seasonal frost and …
Foundations on Fill and Backfilling - 3 PDH
Foundations may be constructed on fills and backfilled material. Fills may include conventional compacted fills; hydraulic fills; and uncontrolled fills of soils or industrial and domestic wastes, such as ashes, slag, chemical wastes, building rubble, and …
Gas Distribution - 3 PDH
This course contains instructions and engineering information relating to gas distribution pipe systems, including pressure regulators, valves, meters, and other necessary appurtenances, for the distribution of fuel gas, natural and manufactured, from the …
Geometrics for Roads and Streets - 3 PDH
This courses discusses the geometric design criteria for roads and streets. It sets forth the approaches and traffic flow criteria for guidance in determining types and configurations best suited for construction.
Geotextiles in Pavement and Drainage Applications - 2 PDH
This course will introduce you to geotextiles made from polypropylene, polyester, polyethylene, polyamide (nylon), polyvinylidene chloride, and fiberglass. You will learn about their physical properties, functions, and design methods. You will also learn …
Heating and Cooling Distribution Systems - 3 PDH
This is an introduction to the design of heating and cooling distribution systems outside of buildings. It provides information about system selection, distribution media selection, and general distribution system design. Discussed are distribution …
High Temperature Water Heating Plants - 5 PDH
This course will introduce you to systems, equipment and design guidelines for high temperature water (HTW) heating plants. HTW systems are used for heating multi-building facilities such as campuses and industrial and commercial activities. The advantage …
Hospital Water Systems - 3 PDH
This course will introduce you to design and construction considerations for domestic water supply systems for hospitals and other health care facilities.
Hot Mix Asphalt Pavement - 5 PDH
This course will tell you about hot-mix asphalt often used for high-performance pavements. The degree of performance required should be selected based on traffic conditions and the availability of satisfactory materials.
How To Become Registered as an Architectural Engineer - 3 PDH
Engineers who have passed the Fundamentals of Engineering (FE) registration examination (formerly called the Engineer-in-Training….EIT exam) or both the FE and the Principles and Practices of Engineering (PE) registration examination in another discipline …
HVAC Systems - 5 PDH
This is a course for all of the members of the building design team. It will give you a basic introduction to air conditioning system design so you can better understand the technology, concepts and terminology in design of air conditioning systems. It …
HVAC Systems for Medical Facilities - 5 PDH
This course will introduce you to heating, ventilating and air conditioning (HVAC) systems for medical facilities such as hospitals and clinics. You will learn about air conditioning requirements, systems, equipment and design practices for the various …
Hydraulic Design of Culverts - 3 PDH
This course will introduce you to a nomographic approach to hydraulic design of culverts. Culverts are hydraulic structures intended to convey, generally, stormwater and other unanticipated flows in and around earth and other structures such as highways, …
Hydraulic Design of Sewers - 3 PDH
This course will introduce you to the principles of hydraulic design of sanitary sewers. You will learn how to calculate quantities of wastewater, the approach to design of gravity and depressed sewers, required pumping capacity, hydrogen sulfide gas …
Hydroelectric Power Plant Structures - 3 PDH
The course discusses location, configuration and design considerations for hydroelectric powerhouses. The factors affecting the location include: Location of the spillway (when powerhouse is located adjacent to the dam). Location of navigation locks (on …
Hydroelectric Power Plants Generator Voltage - 3 PDH
This course discusses the high-voltage system in hydroelectric power plants which includes equipment and conductors that carry current at transmission line-voltage, with their insulators, supports, switching equipment, and protective devices.
Hydroelectric Power Plants High Voltage - 3 PDH
This course discusses the high-voltage system in hydroelectric power plants which includes equipment and conductors that carry current at transmission line-voltage, with their insulators, supports, switching equipment, and protective devices. The system …
Implementing Design-Build in the Public Sector - 5 PDH
Public works project managers are under great pressure to award construction contracts using a loosely defined process called “design-build.” There are benefits that can be realized using design-build as a construction delivery process, but there are …
Impressed Current Cathodic - 3 PDH
This course provides an introduction to impressed current cathodic protection systems. There are two principle methods of providing cathodic protection: sacrificial anode and impressed current. The primary advantage of impressed current cathodic …
Incinerator Emissions and Permitting - 3 PDH
This course describes and quantifies whenever possible the air pollution particulate emissions which are the direct result of the incineration process. The incineration process consists of burning solid, semisolid, liquid, or gaseous waste to produce …