Civil Engineering
Valve Fundamentals - 4 PDH
Valves are widely used in fluid piping systems to shut off or throttle flow, as well as to prevent backflow, reduce pressure or relieve pressure. This course provides information about the basic components of a valve and their function. There is also …
Flow Measurements in Pipes and Ducts - 3 PDH
This course is about measurement of the flow rate of a fluid flowing under pressure in a closed conduit. The closed conduit is often circular, but also may be square or rectangular (such as a heating duct) or any other shape. The other major category of …
Concrete Pavements - 7 PDH
This course provides information on the materials and construction procedures for portland cement concrete pavements. It describes the constituents to be used in concrete, the procedures to be used in manufacturing concrete, and the equipment and …
Hydroelectric Power Plant Structures - 3 PDH
The course discusses location, configuration and design considerations for hydroelectric powerhouses. The factors affecting the location include: Location of the spillway (when powerhouse is located adjacent to the dam). Location of navigation locks (on …
Distribution of Stresses in Soil - 3 PDH
This course covers the analysis of stress conditions at a point, stresses beneath structures and embankments, and empirical methods for estimating loads on buried pipes, conduits, shafts, and tunnels.
Collapse Resistance in Federal Buildings - 10 PDH
Progressive collapse can lead to catastrophic failures, causing widespread damage and loss of life. This course introduces the GSA guidelines, equipping participants with knowledge and tools to design structures capable of withstanding these risks.
Water Supply Systems Operation and Maintenance - 3 PDH
This publication provides an introduction to maintenance inspections and general maintenance services required at domestic water supply systems. It contains information about tools and equipment, lubricants, and materials and supplies required to perform …
Steel Bridge Maintenance - 3 PDH
This course discusses steel bridge maintenance and repair. Preventive maintenance of steel bridge components consists mainly of measures to protect the steel from corrosion. When deicing salt is added to the electrolyte, there is a dramatic increase in …
Domestic Wastewater Treatment - 3 PDH
This course will introduce you to the basics of domestic wastewater treatment. You will learn about preliminary measures, pretreatment, primary, secondary and advanced treatment processes, and sludge treatment and disposal. Approximate performance data …
Retaining Walls And Excavation Support Systems - 3 PDH
Retaining walls must be designed so that foundation pressures do not exceed allowable bearing pressures, wall settlements are tolerable, safety factors against sliding and overturning are adequate, and the wall possesses adequate structural strength. …
Marine Fueling Facilities - 3 PDH
This course provides an introduction to the design of marine applications of petroleum fueling facilities. Design of marine fuel receiving and dispensing facilities for the purpose of receiving fuel and/or loading fuel aboard ships, barges and boats for …
Small Flow Waste Treatment Systems - 3 PDH
This course will introduce you to small flow waste treatment systems such as septic tanks, waterless toilets, filtration and reuse systems, Imhoff tanks, and packaged treatment plants. You will learn about subsurface absorption and how to conduct …
High Temperature Water Heating Plants - 5 PDH
This course will introduce you to systems, equipment and design guidelines for high temperature water (HTW) heating plants. HTW systems are used for heating multi-building facilities such as campuses and industrial and commercial activities. The advantage …
OSHA: Construction, Demolition & Cleanup Safety Issues - 6 PDH
Construction, demolition, and cleanup projects are inherently hazardous. Accident rates in these industries are accordingly higher than in other industries. OSHA’s mission is to reduce these accident rates through safety rules and regulations. This course …
Recycling Construction and Demolition Waste - 3 PDH
There is a significant amount of construction and demolition (C&D) waste developed due to construction activities and structure demolition, for example, at some installations, construction and demolition waste accounts for up to 80 percent of the solid …
Dam Arch Construction - 3 PDH
This course will introduce you to the construction of concrete arch dams. The design and analysis of any dam assumes that the construction will provide a suitable foundation and uniform quality of concrete. The design also depends on the construction to …
Architectural Design: Golf Clubhouses - 3 PDH
This course will introduce you to the fundamentals of golf clubhouse design. You will learn about the fundamentals of site and building design, functional area criteria, space allocations and illustrative designs for small, medium and large clubhouses. …
Deep Foundations - 3 PDH
This course will provide you with an introduction to deep foundations. A deep foundation derives its support from competent strata at significant depths below the surface or, alternatively, has a depth to diameter ratio greater than 4. A deep foundation …
Cathodic Protection Maintenance - 3 PDH
This course will provide you with an introduction to the methods, equipment and practices for inspection and maintenance of cathodic protection systems. Both galvanic (sacrificial anode) and impressed current systems are discussed.
Primary Wastewater Treatment - 3 PDH
Wastewater treatment is usually characterized as consisting of four sequential processes: preliminary, primary, secondary and tertiary treatment. This course will introduce you to processes and equipment for primary treatment of wastewater. You will be …
Water Desalination - 5 PDH
This course will introduce you to water desalination technologies, processes and methods. You will learn the importance of site and water source selection. You will be introduced to an approach for selecting the appropriate desalination technology and …
Fuel Cells Green Power - 3 PDH
Fuel cells are not just laboratory curiosities. While there is much work that needs to be done to optimize the fuel cell system (remember, the gasoline internal combustion engine is nearly 120 years old and still being improved), hydrogen fuel cell …
Pavement Overlays - 3 PDH
Normally, overlays of existing pavements are used to increase the load-carrying capacity of an existing pavement or to correct a defective surface condition on the existing pavement. Of these reasons, the first requires a structural design procedure for …
Carbon Adsorption for Waste Treatment - 3 PDH
This course discusses waste treatment using, primarily, activated carbon. Both liquid and vapor phase adsorption are discussed. Adsorption technologies may be applicable to treatment of both sanitary and industrial waste streams.
Hydraulic Design of Culverts - 3 PDH
This course will introduce you to a nomographic approach to hydraulic design of culverts. Culverts are hydraulic structures intended to convey, generally, stormwater and other unanticipated flows in and around earth and other structures such as highways, …
Design Standards for Federal Public Buildings - 20 PDH
This course introduces participants to its core principles, equipping them with the knowledge to navigate complex standards, implement innovative solutions, and achieve excellence in every project phase.
Water Distribution System Appurtenances - 3 PDH
This publication contains guidance for the operation and maintenance of various types of water distribution system appurtenances. Discussed are valves and hydrants; flow, pressure and level sensors; transmission systems; indicators, registers and …
Bridge Sub-Superstructure Inspection - 3 PDH
This is an introduction to the factors to consider in inspection of bridge superstructures and substructures. This course will help you to address a variety of bridge maintenance issues.