Guyer
Rigid Pavement Design - 3 PDH
This is an introduction to rigid pavement design. It is a basic treatment that will introduce designers to some important principles and terminology. In simple applications on real projects the information provided will give designers a good start in …
Concrete Pavements - 7 PDH
This course provides information on the materials and construction procedures for portland cement concrete pavements. It describes the constituents to be used in concrete, the procedures to be used in manufacturing concrete, and the equipment and …
Hydroelectric Power Plant Structures - 3 PDH
The course discusses location, configuration and design considerations for hydroelectric powerhouses. The factors affecting the location include: Location of the spillway (when powerhouse is located adjacent to the dam). Location of navigation locks (on …
Treated Water Storage - 4 PDH
This course provides an introduction to design criteria for treated water storage requirements at facilities, gives typical design analyses for elevated tanks, standpipes, and reservoirs, and provides guidance on the procedures to be followed in selecting …
Water Supply Systems Operation and Maintenance - 3 PDH
This publication provides an introduction to maintenance inspections and general maintenance services required at domestic water supply systems. It contains information about tools and equipment, lubricants, and materials and supplies required to perform …
Bridge Sub-Superstructure Inspection - 3 PDH
This is an introduction to the factors to consider in inspection of bridge superstructures and substructures. This course will help you to address a variety of bridge maintenance issues.
Hydraulic Design of Sewers - 3 PDH
This course will introduce you to the principles of hydraulic design of sanitary sewers. You will learn how to calculate quantities of wastewater, the approach to design of gravity and depressed sewers, required pumping capacity, hydrogen sulfide gas …
Retaining Walls And Excavation Support Systems - 3 PDH
Retaining walls must be designed so that foundation pressures do not exceed allowable bearing pressures, wall settlements are tolerable, safety factors against sliding and overturning are adequate, and the wall possesses adequate structural strength. …
Marine Fueling Facilities - 3 PDH
This course provides an introduction to the design of marine applications of petroleum fueling facilities. Design of marine fuel receiving and dispensing facilities for the purpose of receiving fuel and/or loading fuel aboard ships, barges and boats for …
Soils: Identification and Classification - 4 PDH
This course will introduce you to the principles and practices of identification and classification of soil and rock. Identification and classification are the essential first steps in soil mechanics and engineering, and engineering of foundations for …
Recycling Construction and Demolition Waste - 3 PDH
There is a significant amount of construction and demolition (C&D) waste developed due to construction activities and structure demolition, for example, at some installations, construction and demolition waste accounts for up to 80 percent of the solid …
Dam Arch Construction - 3 PDH
This course will introduce you to the construction of concrete arch dams. The design and analysis of any dam assumes that the construction will provide a suitable foundation and uniform quality of concrete. The design also depends on the construction to …
Building Design Specifications and Tools - 3 PDH
This course will introduce you to the most important resource available to engineers and architects engaged in the design of buildings and related infrastructure. It represents the collective knowledge of thousands of engineers and architects acquired …
Deep Foundations - 3 PDH
This course will provide you with an introduction to deep foundations. A deep foundation derives its support from competent strata at significant depths below the surface or, alternatively, has a depth to diameter ratio greater than 4. A deep foundation …
Cathodic Protection Maintenance - 3 PDH
This course will provide you with an introduction to the methods, equipment and practices for inspection and maintenance of cathodic protection systems. Both galvanic (sacrificial anode) and impressed current systems are discussed.
Sanitary Landfills - 3 PDH
This is an introduction to the planning and design of sanitary landfills. You will learn about dry and wet landfills, site selection, site development plans, site layout, trench design, leachate control and treatment, gas control, runoff control, support …
Pavement Overlays - 3 PDH
Normally, overlays of existing pavements are used to increase the load-carrying capacity of an existing pavement or to correct a defective surface condition on the existing pavement. Of these reasons, the first requires a structural design procedure for …
Carbon Adsorption for Waste Treatment - 3 PDH
This course discusses waste treatment using, primarily, activated carbon. Both liquid and vapor phase adsorption are discussed. Adsorption technologies may be applicable to treatment of both sanitary and industrial waste streams.
Activated Sludge Wastewater Treatment Plants - 3 PDH
This course provides an introduction to activated sludge wastewater treatment plants. In a conventional (plug-flow) activated sludge plant, the primary-treated wastewater and acclimated micro-organisms (activated sludge or biomass) are aerated in a basin …
Water Distribution System Appurtenances - 3 PDH
This publication contains guidance for the operation and maintenance of various types of water distribution system appurtenances. Discussed are valves and hydrants; flow, pressure and level sensors; transmission systems; indicators, registers and …