Guyer
Area Development Plans - 3 PDH
Area Development Planning PDH provides an introduction to the Area Development Planning (ADP) process that is commonly used in developing new project sites. The planning procedures described are a guide that can be modified to suit specific project …
Hydroelectric Power Plant Structures - 3 PDH
The course discusses location, configuration and design considerations for hydroelectric powerhouses. The factors affecting the location include: Location of the spillway (when powerhouse is located adjacent to the dam). Location of navigation locks (on …
Secondary Wastewater Treatment - 5 PDH
Wastewater treatment is usually characterized as consisting of four sequential processes: preliminary, primary, secondary and tertiary treatment. This course will introduce you to processes and equipment for secondary treatment of wastewater. You will be …
Retaining Walls And Excavation Support Systems - 3 PDH
Retaining walls must be designed so that foundation pressures do not exceed allowable bearing pressures, wall settlements are tolerable, safety factors against sliding and overturning are adequate, and the wall possesses adequate structural strength. …
Cathodic Protection Maintenance - 3 PDH
This course will provide you with an introduction to the methods, equipment and practices for inspection and maintenance of cathodic protection systems. Both galvanic (sacrificial anode) and impressed current systems are discussed.
Ethical Issues: The Tacoma Narrows Bridge Collapse - 3 PDH
This course will examine the ethical issues that arose from the 1940 collapse of the Tacoma Narrows bridge in Washington state. This was one of the most dramatic bridge collapses in history, with fortunately no loss of life and little property damage …
Coatings and Paints - 5 PDH
Painting and coating of surfaces in buildings and other infrastructure construction require careful attention to specification, application and inspection if construction materials are to be effectively protected for a substantial service life. This …
Drainage Pipe Strength, Cover, and Bedding - 3 PDH
This course provides an introduction to drainage pipe strength, cover and bedding. A drainage pipe is defined as a structure (other than a bridge) to convey water through a trench or under a fill or some other obstruction. Materials for permanent-type …
Petroleum Atmospheric Tanks - 5 PDH
This course provides guidance for the design of atmospheric storage tanks for storage of petroleum fuels. Underground and aboveground tanks in both horizontal and vertical configuration are discussed.
Auxiliary Power Systems Switchboard - 3 PDH
This publication provides technical guidance and design requirements for operation and maintenance of auxiliary electric power systems.
Plumbing and Gas Systems For Medical Facilities - 4 PDH
This course will introduce you to the basics of designing plumbing and gas systems for medical treatment facilities such as hospitals, medical and dental offices, and clinical and research medical and dental laboratories. You will learn about plumbing …
Design of Solar Water Heating Systems - 3 PDH
This course presents the information required to design a solar energy water heating system, after planning and system selection have been completed.
Architectural Theatres Vol. 3 - 3 PDH
This publication provides an introduction to certain aspects of the architectural design of theatres and concert halls. This volume discusses access, environmental systems, and performance support spaces.. Topics discussed include audience access, …
Electric Power Requirements for Buildings - 3 PDH
This course will introduce you to an approach you can use to determine electric power requirements for buildings and multi-building developments and activities. You will learn about terminology, and acquisition and analysis of preliminary load data you …
Area Drainage Systems - 5 PDH
This course will introduce you to normal requirements for design of surface and subsurface drainage systems for residential, commercial, institutional and industrial areas.
Solar Cooling Systems - 3 PDH
This course will introduce you to solar-powered cooling systems for buildings. You will learn about absorption cooling systems, Rankine cycle heat engine cooling systems, desiccant cooling, and other solar-powered systems having potential for commercial …
Concrete Pavements - 7 PDH
This course provides information on the materials and construction procedures for portland cement concrete pavements. It describes the constituents to be used in concrete, the procedures to be used in manufacturing concrete, and the equipment and …
Energy Efficient HVAC Controls - 3 PDH
This course covers automatic temperature and humidity controls, space pressurization controls, safety controls, and energy monitoring and central supervisory control systems for heating, ventilating and air conditioning (HVAC) systems. The control system …
Theatres Vol. 2 - 3 PDH
This publication provides an introduction to certain aspects of the architectural design of theatres and concert halls. This volume discusses accessory equipment. Topics discussed include general considerations, classification of accessory facilities, …
Hydraulic Design of Sewers - 3 PDH
This course will introduce you to the principles of hydraulic design of sanitary sewers. You will learn how to calculate quantities of wastewater, the approach to design of gravity and depressed sewers, required pumping capacity, hydrogen sulfide gas …
Distribution of Stresses in Soil - 3 PDH
This course covers the analysis of stress conditions at a point, stresses beneath structures and embankments, and empirical methods for estimating loads on buried pipes, conduits, shafts, and tunnels.
Water Supply Systems Operation and Maintenance - 3 PDH
This publication provides an introduction to maintenance inspections and general maintenance services required at domestic water supply systems. It contains information about tools and equipment, lubricants, and materials and supplies required to perform …
Boiler Control Systems: An Introduction - 4 PDH
This course provides an introduction to criteria for the design of heating plant instrumentation. A heating plant may contain one or more boilers. The plant may be an individual plant serving a single building or a compact group of buildings, or a …
Carbon Adsorption for Waste Treatment - 3 PDH
This course discusses waste treatment using, primarily, activated carbon. Both liquid and vapor phase adsorption are discussed. Adsorption technologies may be applicable to treatment of both sanitary and industrial waste streams.
Sludge Handling, Treatment and Disposal - 5 PDH
This course will introduce you to processes and equipment for handling, treating and disposing of sludge produced by wastewater treatment plants. You will learn about sludge pumping, thickening, conditioning, dewatering, digestion, storage and final …
Seepage and Drainage - 7 PDH
This course covers surface erosion, and analysis of flow quantity and groundwater pressures associated with underseepage. Requirements are given for methods of drainage and pressure relief. Control of soil erosion must be considered in all new …
Cathodic Protection Principles - 5 PDH
This course will provide you with an introduction to the principles of cathodic protection for underground and underwater structures. You will be introduced to the physics and chemistry of the corrosion process and how to mitigate the corrosion using …
Petroleum Facilities General - 3 PDH
This course provides general information about petroleum products as a basis for the design of bulk fuel storage facilities, including bulk storage tanks and those components normally located within a typical bulk storage compound. These components …
Fire Protection Engineering for Buildings - 3 PDH
This course will introduce you to fire protection engineering fundamentals related to building materials and design, water supply for fire protection, fire extinguishing systems, fire alarm systems, special occupancies and hazards, and storage of …
High Temperature Water Heating Plants - 5 PDH
This course will introduce you to systems, equipment and design guidelines for high temperature water (HTW) heating plants. HTW systems are used for heating multi-building facilities such as campuses and industrial and commercial activities. The advantage …
Recycling Construction and Demolition Waste - 3 PDH
There is a significant amount of construction and demolition (C&D) waste developed due to construction activities and structure demolition, for example, at some installations, construction and demolition waste accounts for up to 80 percent of the solid …
Prime Movers Auxiliary Power Systems - 5 PDH
This publication contains guidance for operation, maintenance and repair of prime movers in auxiliary electric power generating systems. Discussion includes the most common prime movers: diesel engines and gas turbine engines.
Preliminary Wastewater Treatment - 3 PDH
This course will introduce you to processes and equipment for preliminary treatment of wastewater. You will be introduced to descriptions, functions and design considerations for bar screens, comminuting devices, grit chambers, proportional weirs, …
Earthwork for Foundations - 3 PDH
This course provides an introduction to earthwork for foundations. In general, excavation for subsurface structures will consist of open excavation and shaft and tunnel excavation. Where excavation to great depths is required, a variety of soils and rock …
Architectural Theatres Vol. 4 - 3 PDH
This publication provides an introduction to certain aspects of the architectural design of theatres and concert halls. This volume discusses theatre lighting, scenery and soft goods, and rigging and stage mechanisms. Topics discussed include audience …
Electrical Systems for Medical Facilities - 5 PDH
This course will introduce you to electrical systems for medical facilities, including hospitals, medical and dental clinics, and medical and dental laboratories. You will learn about general electrical requirements, exterior electrical systems, alternate …
Levees Seepage Slope Settlement - 3 PDH
This course will introduce you to methods for controlling seepage and settlement in the construction of levees, and to generally acceptable guidelines for levee slopes. Without control, underseepage in pervious foundations beneath levees may result in (a) …
Sustainable Design for Buildings - 3 PDH
“Sustainable design” is no longer a boutique concept in the design and construction of buildings and related infrastructure. It is widely required by government agencies and is becoming more and more in demand by responsible private owners. This webinar …
Pavement Overlays - 3 PDH
Normally, overlays of existing pavements are used to increase the load-carrying capacity of an existing pavement or to correct a defective surface condition on the existing pavement. Of these reasons, the first requires a structural design procedure for …
Fire Suppression ITM - 3 PDH
This course will introduce you to best practices for inspection, testing and maintenance of fire detection, alarm and suppression systems to assure reliable and effective operation in emergency situations. You will be introduced to the principles of …
Treatment Boiler Water - 5 PDH
This course provides an introduction to the treatment of steam boiler water to prevent buildup of harmful chemicals that can cause harmful corrosion, sludge buildup and other conditions that reduce the efficiency and service life of a boiler and its …
Implementing Design-Build in the Public Sector - 5 PDH
Public works project managers are under great pressure to award construction contracts using a loosely defined process called “design-build.” There are benefits that can be realized using design-build as a construction delivery process, but there are …
Hydraulic Design of Culverts - 3 PDH
This course will introduce you to a nomographic approach to hydraulic design of culverts. Culverts are hydraulic structures intended to convey, generally, stormwater and other unanticipated flows in and around earth and other structures such as highways, …
Water Distribution System Appurtenances - 3 PDH
This publication contains guidance for the operation and maintenance of various types of water distribution system appurtenances. Discussed are valves and hydrants; flow, pressure and level sensors; transmission systems; indicators, registers and …
Building Design Specifications and Tools - 3 PDH
This course will introduce you to the most important resource available to engineers and architects engaged in the design of buildings and related infrastructure. It represents the collective knowledge of thousands of engineers and architects acquired …
Dam Arch Manual Design Layout - 3 PDH
This course will introduce you to a methodology for manual layout of concrete arch dams. In practice layout of concrete arch dams is, of course, a computerized process, but understanding an approach to manual layout will be an excellent way to gain an …
Small Flow Waste Treatment Systems - 3 PDH
This course will introduce you to small flow waste treatment systems such as septic tanks, waterless toilets, filtration and reuse systems, Imhoff tanks, and packaged treatment plants. You will learn about subsurface absorption and how to conduct …
Settlement and Volume Expansion in Soils -5 PDH
This course concerns (a) immediate settlements, (b) long-term settlements, (c) rate of settlement, (d) criteria for tolerable settlement, (e) methods of reducing or accelerating settlements for saturated fine-grained soils and (f) methods for controlling …