Guyer
Foundations on Fill and Backfilling - 3 PDH
Foundations may be constructed on fills and backfilled material. Fills may include conventional compacted fills; hydraulic fills; and uncontrolled fills of soils or industrial and domestic wastes, such as ashes, slag, chemical wastes, building rubble, and …
Impressed Current Cathodic - 3 PDH
This course provides an introduction to impressed current cathodic protection systems. There are two principle methods of providing cathodic protection: sacrificial anode and impressed current. The primary advantage of impressed current cathodic …
Carbon Adsorption for Waste Treatment - 3 PDH
This course discusses waste treatment using, primarily, activated carbon. Both liquid and vapor phase adsorption are discussed. Adsorption technologies may be applicable to treatment of both sanitary and industrial waste streams.
Drainage Pipe Strength, Cover, and Bedding - 3 PDH
This course provides an introduction to drainage pipe strength, cover and bedding. A drainage pipe is defined as a structure (other than a bridge) to convey water through a trench or under a fill or some other obstruction. Materials for permanent-type …
Incinerator Emissions and Permitting - 3 PDH
This course describes and quantifies whenever possible the air pollution particulate emissions which are the direct result of the incineration process. The incineration process consists of burning solid, semisolid, liquid, or gaseous waste to produce …
Cathodic Protection Maintenance - 3 PDH
This course will provide you with an introduction to the methods, equipment and practices for inspection and maintenance of cathodic protection systems. Both galvanic (sacrificial anode) and impressed current systems are discussed.
Security Fences - 3 PDH
This course applies to all construction, renovation, and repair projects including temporary construction that includes security fencing and gates. Security fences and gates are installed and used primarily to define the perimeter of protected areas, such …
Steam Generators - 3 PDH
This course addresses the design requirements for gas, oil, coal, and waste fuel fired steam generating, water-tube boilers and components with steam capacities between 20,000 and 250,000 pph and maximum pressures of 450 pounds per inch gauge …
Interior Lighting Design - 3 PDH
This course will introduce you to principles of lighting design for building interiors. The concepts and considerations of visibility, glare, uniformity and illuminance will be explained and discussed. You will learn about lighting controls and their …
Air Quality Boiler Plants - 5 PDH
This publication provides an introduction to air quality control and monitoring equipment for fuel fired plants such as steam boiler plants. Included are discussions of chemical, cooling and sump pumps, nitrogen and carbon dioxide systems, ash handling, …
Foundations In Areas of Significant Frost Penetration - 3 PDH
Areas of significant frost penetration may be defined as those in which freezing temperatures occur in the ground to sufficient depth to be a significant factor in foundation design. These areas may be further characterized as seasonal frost and …
Makeup Water Industrial Water - 3 PDH
This course provides an introduction to makeup water for Industrial water systems. Many installations use fresh water and, often, potable water. Makeup water, often referred to as “makeup,” is fresh water that is added to an industrial water system to …
Levees Seepage Slope Settlement - 3 PDH
This course will introduce you to methods for controlling seepage and settlement in the construction of levees, and to generally acceptable guidelines for levee slopes. Without control, underseepage in pervious foundations beneath levees may result in (a) …
Recycling Construction and Demolition Waste - 3 PDH
There is a significant amount of construction and demolition (C&D) waste developed due to construction activities and structure demolition, for example, at some installations, construction and demolition waste accounts for up to 80 percent of the solid …
Interior Electrical Distribution Systems - 3 PDH
This publication provides an introduction to interior electrical distribution systems for buildings and related infrastructure. Topics covered include transformers, service entrances, switchgear, switchboards, panelboards, motor controls and motor …
Cathodic Protection Principles - 5 PDH
This course will provide you with an introduction to the principles of cathodic protection for underground and underwater structures. You will be introduced to the physics and chemistry of the corrosion process and how to mitigate the corrosion using …
Theatre Acoustics - 3 PDH
This course will provide you with an introduction to the techniques and methods applicable to design of concert halls and theatres for optimal acoustic characteristics and communications.
Structural Design Criteria for Buildings - 3 PDH
This course introduces you to structural design criteria for the design of buildings. Included is technical guidance for buildings constructed of concrete, masonry, steel and wood. Criteria are also included for pre-engineered metal buildings, slabs on …
Passive Solar Buildings - 3 PDH
This course is an introduction to passive solar technology to heat buildings. It will tell you about the basic passive systems and climate considerations you need to know about. You will gain knowledge about guidelines for schematic design of passive …
Air Traffic Control Facilities - 3 PDH
This publication provides an introduction to the planning and design of air traffic control facilities, such as would be required at airports and airfields. Building-types discussed are the Terminal Radar Approach Control Facility, Area Control and …
Pavement Design in Seasonal Frost Conditions - 5 PDH
This publication presents criteria and procedures for the design and construction of pavements placed on subgrade or base course materials subject to seasonal frost action. The most prevalent modes of distress in pavements and their causes are listed. The …
Marine Fueling Facilities - 3 PDH
This course provides an introduction to the design of marine applications of petroleum fueling facilities. Design of marine fuel receiving and dispensing facilities for the purpose of receiving fuel and/or loading fuel aboard ships, barges and boats for …
Dam Arch Construction - 3 PDH
This course will introduce you to the construction of concrete arch dams. The design and analysis of any dam assumes that the construction will provide a suitable foundation and uniform quality of concrete. The design also depends on the construction to …
Stormwater Drainage and Site Development - 3 PDH
This publication provides an introduction to stormwater drainage systems and improvements for land development projects, and strategies and considerations in site development.
Central Heating Plant Planning - 3 PDH
This publication contains data and information as criteria to guide the planning of steam and high temperature water (HTW) central and individual heating plants. Engineering and economic considerations are identified to guide siting decisions, fuel …
Constructing Maintaining Cathodic Protection - 3 PDH
This course will provide you with an introduction to the principles of cathodic protection for underground and underwater structures. You will be introduced to the physics and chemistry of the corrosion process and how to mitigate the corrosion using …
Theatres Vol. 1 - 5 PDH
This publication provides an introduction to certain aspects of the architectural design of theatres and concert halls. Topics discussed include room characteristics, drama and music room qualities, house, stage, and primary and secondary uses. This …
Bearing Capacity Analysis - 3 PDH
This course will introduce you to methods for analysis of soils and rock to determine load bearing capacity. Stresses transmitted by a foundation to underlying soils must not cause bearing-capacity failure or excessive foundation settlement. The design …
Roofing Systems - 5 PDH
This is an introduction to roofing systems. You will learn how to specify roofing systems and incorporate appropriate engineering details into your working drawings on a wide variety of projects. You will learn about the different types of roofing systems …
Architectural Theatres Vol. 3 - 3 PDH
This publication provides an introduction to certain aspects of the architectural design of theatres and concert halls. This volume discusses access, environmental systems, and performance support spaces.. Topics discussed include audience access, …
Petroleum Atmospheric Tanks - 5 PDH
This course provides guidance for the design of atmospheric storage tanks for storage of petroleum fuels. Underground and aboveground tanks in both horizontal and vertical configuration are discussed.
Planning Solar Water Heating Systems - 3 PDH
This course provides guidance for the planning of active solar energy systems to preheat domestic and service water. The systems treated by this publication are liquid based. Guidelines apply to the larger commercial-scale applications that require an …
Waste Treatment Carbon Adsorption Applications - 3 PDH
This course discusses waste treatment using, primarily, activated carbon. Both liquid and vapor phase adsorption are discussed. Adsorption technologies may be applicable to treatment of both sanitary and industrial waste streams.
Trickling Filter Wastewater Treatment Plants - 3 PDH
This course provides an introduction to trickling filter wastewater treatment plants. Trickling filter plants have been justified by their low initial cost, low operating and maintenance costs, and relative simplicity of operation. Although the effluent …
Deep Foundations - 3 PDH
This course will provide you with an introduction to deep foundations. A deep foundation derives its support from competent strata at significant depths below the surface or, alternatively, has a depth to diameter ratio greater than 4. A deep foundation …
Cooling Tower Water Treatment - 3 PDH
Cooling water systems remove heat generated from a variety of industrial processes. There are three basic types of cooling water systems: once-through, open recirculating, and closed recirculating cooling water systems. This publication describes water …
Theatres Vol. 2 - 3 PDH
This publication provides an introduction to certain aspects of the architectural design of theatres and concert halls. This volume discusses accessory equipment. Topics discussed include general considerations, classification of accessory facilities, …
Pavement Overlays - 3 PDH
Normally, overlays of existing pavements are used to increase the load-carrying capacity of an existing pavement or to correct a defective surface condition on the existing pavement. Of these reasons, the first requires a structural design procedure for …
Sustainable Design for Buildings - 3 PDH
“Sustainable design” is no longer a boutique concept in the design and construction of buildings and related infrastructure. It is widely required by government agencies and is becoming more and more in demand by responsible private owners. This webinar …
Architectural Theatres Vol. 4 - 3 PDH
This publication provides an introduction to certain aspects of the architectural design of theatres and concert halls. This volume discusses theatre lighting, scenery and soft goods, and rigging and stage mechanisms. Topics discussed include audience …
Petroleum Facilities General - 3 PDH
This course provides general information about petroleum products as a basis for the design of bulk fuel storage facilities, including bulk storage tanks and those components normally located within a typical bulk storage compound. These components …
Retaining Walls And Excavation Support Systems - 3 PDH
Retaining walls must be designed so that foundation pressures do not exceed allowable bearing pressures, wall settlements are tolerable, safety factors against sliding and overturning are adequate, and the wall possesses adequate structural strength. …
Water Cooling Towers - 3 PDH
Cooling water systems remove heat generated from a variety of industrial processes. There are three basic types of cooling water systems: once-through, open recirculating, and closed recirculating cooling water systems. This course describes once-through …
Tropical Engineering: Building Envelope - 3 PDH
This publication provides an introduction to design of building envelopes in tropical climates where heat and humidity are important considerations. Discussed are roofing, wall materials, windows, doors, finishes and miscellaneous specialties.
Design of Solar Water Heating Systems - 3 PDH
This course presents the information required to design a solar energy water heating system, after planning and system selection have been completed.
Energy Efficient HVAC Controls - 3 PDH
This course covers automatic temperature and humidity controls, space pressurization controls, safety controls, and energy monitoring and central supervisory control systems for heating, ventilating and air conditioning (HVAC) systems. The control system …
Water Sampling Testing - 3 PDH
Water sampling and testing procedures provide information that can be used for the following purposes: to ensure the protection of the water system equipment; to prevent unexpected system failure; to provide information used to control water quality; and …
Roller-Compacted Concrete Pavements - 3 PDH
Procedures and criteria described here are applicable to the design and construction of roller-compacted concrete (RCC) pavement (RCCP). Roller-compacted concrete pavement employs a concrete paving technology that involves laydown and compaction of a …