All Courses
Prime Movers Auxiliary Power Systems - 5 PDH
This publication contains guidance for operation, maintenance and repair of prime movers in auxiliary electric power generating systems. Discussion includes the most common prime movers: diesel engines and gas turbine engines.
Primary Wastewater Treatment - 3 PDH
Wastewater treatment is usually characterized as consisting of four sequential processes: preliminary, primary, secondary and tertiary treatment. This course will introduce you to processes and equipment for primary treatment of wastewater. You will be …
Preliminary Wastewater Treatment - 3 PDH
This course will introduce you to processes and equipment for preliminary treatment of wastewater. You will be introduced to descriptions, functions and design considerations for bar screens, comminuting devices, grit chambers, proportional weirs, …
Plumbing and Gas Systems For Medical Facilities - 4 PDH
This course will introduce you to the basics of designing plumbing and gas systems for medical treatment facilities such as hospitals, medical and dental offices, and clinical and research medical and dental laboratories. You will learn about plumbing …
Planning Solar Water Heating Systems - 3 PDH
This course provides guidance for the planning of active solar energy systems to preheat domestic and service water. The systems treated by this publication are liquid based. Guidelines apply to the larger commercial-scale applications that require an …
Petroleum Pipelines - 3 PDH
This discussion provides guidance for the design of pipelines. Pipelines are typically either interterminal pipelines which are cross country and connect installations, or installation pipelines which connect petroleum-oil-lubricants (POL) facilities …
Petroleum Facilities General - 3 PDH
This course provides general information about petroleum products as a basis for the design of bulk fuel storage facilities, including bulk storage tanks and those components normally located within a typical bulk storage compound. These components …
Petroleum Atmospheric Tanks - 5 PDH
This course provides guidance for the design of atmospheric storage tanks for storage of petroleum fuels. Underground and aboveground tanks in both horizontal and vertical configuration are discussed.
Pavement Overlays - 3 PDH
Normally, overlays of existing pavements are used to increase the load-carrying capacity of an existing pavement or to correct a defective surface condition on the existing pavement. Of these reasons, the first requires a structural design procedure for …
Pavement Design in Seasonal Frost Conditions - 5 PDH
This publication presents criteria and procedures for the design and construction of pavements placed on subgrade or base course materials subject to seasonal frost action. The most prevalent modes of distress in pavements and their causes are listed. The …
Passive Solar Buildings - 3 PDH
This course is an introduction to passive solar technology to heat buildings. It will tell you about the basic passive systems and climate considerations you need to know about. You will gain knowledge about guidelines for schematic design of passive …
OSHA: Fatalities from Improper Work Practices - 4 PDH
This course is based on case studies taken from the Occupational Safety and Health Administration’s “Fatal Facts” —descriptions of accidents in which one or more workers died because of improper work practices. Reading and thinking about these case …
OSHA: Construction, Demolition & Cleanup Safety Issues - 6 PDH
Construction, demolition, and cleanup projects are inherently hazardous. Accident rates in these industries are accordingly higher than in other industries. OSHA’s mission is to reduce these accident rates through safety rules and regulations. This course …
Noise Control in Buildings - 5 PDH
This course will introduce you to the basic principles and terminology of acoustics, and noise control engineering in buildings. You will learn about sound pressure levels, sound power levels, sound intensity levels, vibration levels, frequency, temporal …
Methods for Cleaning Contaminated Soils - 4 PDH
EPA uses many methods to clean up pollution at Superfund and other sites. This course presents various EPA-approved methods for cleaning contaminated soils. For each method, the course describes 1) how the method works, 2) how safe it is, 3) how long it …
Marine Fueling Facilities - 3 PDH
This course provides an introduction to the design of marine applications of petroleum fueling facilities. Design of marine fuel receiving and dispensing facilities for the purpose of receiving fuel and/or loading fuel aboard ships, barges and boats for …
Makeup Water Industrial Water - 3 PDH
This course provides an introduction to makeup water for Industrial water systems. Many installations use fresh water and, often, potable water. Makeup water, often referred to as “makeup,” is fresh water that is added to an industrial water system to …
Low Impact Development - 5 PDH
This course will introduce you to some of the basic concepts of Low Impact Development (LID) …. a stormwater management strategy concerned with maintaining or restoring the natural hydrologic functions of a site to achieve natural resource protection …
Levees Seepage Slope Settlement - 3 PDH
This course will introduce you to methods for controlling seepage and settlement in the construction of levees, and to generally acceptable guidelines for levee slopes. Without control, underseepage in pervious foundations beneath levees may result in (a) …
Landfill Gas Systems - 3 PDH
This course discusses the need for an operation and maintenance (O&M) plan for a landfill gas collection system that addresses the following: extraction wells; LFG monitoring probes; condensate collection and treatment; and flare station. A site-specific …
Laboratory Testing of Soils - 5 PDH
This course will introduce you to the principles and practices of laboratory testing of soils. You will learn about index property, permeability, consolidation, and shear strength tests. You will be introduced to dynamic testing methods, and tests on …
Introduction to Solar Energy - 4 PDH
Solar energy travels from the sun to the earth in the form of electromagnetic radiation. In this course properties of electromagnetic radiation will be discussed and basic calculations for electromagnetic radiation will be described. Several solar …
Interior Lighting Design - 3 PDH
This course will introduce you to principles of lighting design for building interiors. The concepts and considerations of visibility, glare, uniformity and illuminance will be explained and discussed. You will learn about lighting controls and their …
Interior Electrical Distribution Systems - 3 PDH
This publication provides an introduction to interior electrical distribution systems for buildings and related infrastructure. Topics covered include transformers, service entrances, switchgear, switchboards, panelboards, motor controls and motor …
Incinerator Emissions and Permitting - 3 PDH
This course describes and quantifies whenever possible the air pollution particulate emissions which are the direct result of the incineration process. The incineration process consists of burning solid, semisolid, liquid, or gaseous waste to produce …
Impressed Current Cathodic - 3 PDH
This course provides an introduction to impressed current cathodic protection systems. There are two principle methods of providing cathodic protection: sacrificial anode and impressed current. The primary advantage of impressed current cathodic …
Implementing Design-Build in the Public Sector - 5 PDH
Public works project managers are under great pressure to award construction contracts using a loosely defined process called “design-build.” There are benefits that can be realized using design-build as a construction delivery process, but there are …
Hydroelectric Power Plants High Voltage - 3 PDH
This course discusses the high-voltage system in hydroelectric power plants which includes equipment and conductors that carry current at transmission line-voltage, with their insulators, supports, switching equipment, and protective devices. The system …
Hydroelectric Power Plants Generator Voltage - 3 PDH
This course discusses the high-voltage system in hydroelectric power plants which includes equipment and conductors that carry current at transmission line-voltage, with their insulators, supports, switching equipment, and protective devices.
Hydroelectric Power Plant Structures - 3 PDH
The course discusses location, configuration and design considerations for hydroelectric powerhouses. The factors affecting the location include: Location of the spillway (when powerhouse is located adjacent to the dam). Location of navigation locks (on …
Hydraulic Jumps and Non-Uniform Open Channel Flow - 2 PDH
Many examples of open channel flow can be approximated as uniform flow allowing the Manning equation to be used. Non-uniform flow calculations are needed, however, in some open channel flow situations, where the flow is clearly non-uniform. The concepts …
Hydraulic Design of Storm Sewers with Excel - 4 PDH
Storm sewers are widely used to carry away runoff from storms, primarily in urban areas. The hydraulic design begins after the locations for the manholes for the system have been determined. Between each pair of manholes the storm sewer will have a …
Hydraulic Design of Sewers - 3 PDH
This course will introduce you to the principles of hydraulic design of sanitary sewers. You will learn how to calculate quantities of wastewater, the approach to design of gravity and depressed sewers, required pumping capacity, hydrogen sulfide gas …
Hydraulic Design of Culverts - 3 PDH
This course will introduce you to a nomographic approach to hydraulic design of culverts. Culverts are hydraulic structures intended to convey, generally, stormwater and other unanticipated flows in and around earth and other structures such as highways, …
HVAC Systems for Medical Facilities - 5 PDH
This course will introduce you to heating, ventilating and air conditioning (HVAC) systems for medical facilities such as hospitals and clinics. You will learn about air conditioning requirements, systems, equipment and design practices for the various …
HVAC Systems - 5 PDH
This is a course for all of the members of the building design team. It will give you a basic introduction to air conditioning system design so you can better understand the technology, concepts and terminology in design of air conditioning systems. It …
How To Become Registered as an Architectural Engineer - 3 PDH
Engineers who have passed the Fundamentals of Engineering (FE) registration examination (formerly called the Engineer-in-Training….EIT exam) or both the FE and the Principles and Practices of Engineering (PE) registration examination in another discipline …
Hot Mix Asphalt Pavement - 5 PDH
This course will tell you about hot-mix asphalt often used for high-performance pavements. The degree of performance required should be selected based on traffic conditions and the availability of satisfactory materials.
Hospital Water Systems - 3 PDH
This course will introduce you to design and construction considerations for domestic water supply systems for hospitals and other health care facilities.
High Temperature Water Heating Plants - 5 PDH
This course will introduce you to systems, equipment and design guidelines for high temperature water (HTW) heating plants. HTW systems are used for heating multi-building facilities such as campuses and industrial and commercial activities. The advantage …
Heating and Cooling of Agitated Liquid Batches - 3 PDH
The course developed the derivation of the heating and cooling application equations, along with simplifying assumptions. Two examples were given: heating in a jacketed agitated vessel, and cooling with a submerged coil in an agitated tank. The physical …
Heating and Cooling Distribution Systems - 3 PDH
This is an introduction to the design of heating and cooling distribution systems outside of buildings. It provides information about system selection, distribution media selection, and general distribution system design. Discussed are distribution …
Geotextiles in Pavement and Drainage Applications - 2 PDH
This course will introduce you to geotextiles made from polypropylene, polyester, polyethylene, polyamide (nylon), polyvinylidene chloride, and fiberglass. You will learn about their physical properties, functions, and design methods. You will also learn …
Geometrics for Roads and Streets - 3 PDH
This courses discusses the geometric design criteria for roads and streets. It sets forth the approaches and traffic flow criteria for guidance in determining types and configurations best suited for construction.
Gas Distribution - 3 PDH
This course contains instructions and engineering information relating to gas distribution pipe systems, including pressure regulators, valves, meters, and other necessary appurtenances, for the distribution of fuel gas, natural and manufactured, from the …
Fuel Cells Green Power - 3 PDH
Fuel cells are not just laboratory curiosities. While there is much work that needs to be done to optimize the fuel cell system (remember, the gasoline internal combustion engine is nearly 120 years old and still being improved), hydrogen fuel cell …
Foundations on Fill and Backfilling - 3 PDH
Foundations may be constructed on fills and backfilled material. Fills may include conventional compacted fills; hydraulic fills; and uncontrolled fills of soils or industrial and domestic wastes, such as ashes, slag, chemical wastes, building rubble, and …
Foundations In Areas of Significant Frost Penetration - 3 PDH
Areas of significant frost penetration may be defined as those in which freezing temperatures occur in the ground to sufficient depth to be a significant factor in foundation design. These areas may be further characterized as seasonal frost and …