Structural Engineering
Bearing Capacity Analysis - 3 PDH
This course will introduce you to methods for analysis of soils and rock to determine load bearing capacity. Stresses transmitted by a foundation to underlying soils must not cause bearing-capacity failure or excessive foundation settlement. The design …
Petroleum Atmospheric Tanks - 5 PDH
This course provides guidance for the design of atmospheric storage tanks for storage of petroleum fuels. Underground and aboveground tanks in both horizontal and vertical configuration are discussed.
Tropical Engineering: Mechanical, Electrical, Miscellaneous - 3 PDH
This course provides an introduction to special considerations in design of plumbing, HVAC, electrical distribution and miscellaneous features and systems in tropical climates where high humidity, heat, heavy rain and seafront conditions are common.
Interior Electrical Distribution Systems - 3 PDH
This publication provides an introduction to interior electrical distribution systems for buildings and related infrastructure. Topics covered include transformers, service entrances, switchgear, switchboards, panelboards, motor controls and motor …
Planning Solar Water Heating Systems - 3 PDH
This course provides guidance for the planning of active solar energy systems to preheat domestic and service water. The systems treated by this publication are liquid based. Guidelines apply to the larger commercial-scale applications that require an …
Constructing Maintaining Cathodic Protection - 3 PDH
This course will provide you with an introduction to the principles of cathodic protection for underground and underwater structures. You will be introduced to the physics and chemistry of the corrosion process and how to mitigate the corrosion using …
Drainage Pipe Strength, Cover, and Bedding - 3 PDH
This course provides an introduction to drainage pipe strength, cover and bedding. A drainage pipe is defined as a structure (other than a bridge) to convey water through a trench or under a fill or some other obstruction. Materials for permanent-type …
Structural Aluminum Performance-Based Design - 4 PDH
The core concept discussed in this document presents a broad overview of Performance-Based Structural Aluminum design employing various aluminum grades and aluminum alloys.
Deep Foundations - 3 PDH
This course will provide you with an introduction to deep foundations. A deep foundation derives its support from competent strata at significant depths below the surface or, alternatively, has a depth to diameter ratio greater than 4. A deep foundation …
Architectural Theatres Vol. 3 - 3 PDH
This publication provides an introduction to certain aspects of the architectural design of theatres and concert halls. This volume discusses access, environmental systems, and performance support spaces.. Topics discussed include audience access, …
Concrete Pavements - 7 PDH
This course provides information on the materials and construction procedures for portland cement concrete pavements. It describes the constituents to be used in concrete, the procedures to be used in manufacturing concrete, and the equipment and …
Petroleum Facilities General - 3 PDH
This course provides general information about petroleum products as a basis for the design of bulk fuel storage facilities, including bulk storage tanks and those components normally located within a typical bulk storage compound. These components …
Water Supply Systems Operation and Maintenance - 3 PDH
This publication provides an introduction to maintenance inspections and general maintenance services required at domestic water supply systems. It contains information about tools and equipment, lubricants, and materials and supplies required to perform …
OSHA: Fatalities from Improper Work Practices - 4 PDH
This course is based on case studies taken from the Occupational Safety and Health Administration’s “Fatal Facts” —descriptions of accidents in which one or more workers died because of improper work practices. Reading and thinking about these case …
Retaining Walls And Excavation Support Systems - 3 PDH
Retaining walls must be designed so that foundation pressures do not exceed allowable bearing pressures, wall settlements are tolerable, safety factors against sliding and overturning are adequate, and the wall possesses adequate structural strength. …
Cooling Tower Water Treatment - 3 PDH
Cooling water systems remove heat generated from a variety of industrial processes. There are three basic types of cooling water systems: once-through, open recirculating, and closed recirculating cooling water systems. This publication describes water …
Recycling Construction and Demolition Waste - 3 PDH
There is a significant amount of construction and demolition (C&D) waste developed due to construction activities and structure demolition, for example, at some installations, construction and demolition waste accounts for up to 80 percent of the solid …
Steel Bridge Maintenance - 3 PDH
This course discusses steel bridge maintenance and repair. Preventive maintenance of steel bridge components consists mainly of measures to protect the steel from corrosion. When deicing salt is added to the electrolyte, there is a dramatic increase in …
Design of Solar Water Heating Systems - 3 PDH
This course presents the information required to design a solar energy water heating system, after planning and system selection have been completed.
Architectural Theatres Vol. 4 - 3 PDH
This publication provides an introduction to certain aspects of the architectural design of theatres and concert halls. This volume discusses theatre lighting, scenery and soft goods, and rigging and stage mechanisms. Topics discussed include audience …