All Courses
Prime Movers Auxiliary Power Systems - 5 PDH
This publication contains guidance for operation, maintenance and repair of prime movers in auxiliary electric power generating systems. Discussion includes the most common prime movers: diesel engines and gas turbine engines.
Earthwork for Foundations - 3 PDH
This course provides an introduction to earthwork for foundations. In general, excavation for subsurface structures will consist of open excavation and shaft and tunnel excavation. Where excavation to great depths is required, a variety of soils and rock …
Architectural Theatres Vol. 4 - 3 PDH
This publication provides an introduction to certain aspects of the architectural design of theatres and concert halls. This volume discusses theatre lighting, scenery and soft goods, and rigging and stage mechanisms. Topics discussed include audience …
Interior Lighting Design - 3 PDH
This course will introduce you to principles of lighting design for building interiors. The concepts and considerations of visibility, glare, uniformity and illuminance will be explained and discussed. You will learn about lighting controls and their …
Levees Seepage Slope Settlement - 3 PDH
This course will introduce you to methods for controlling seepage and settlement in the construction of levees, and to generally acceptable guidelines for levee slopes. Without control, underseepage in pervious foundations beneath levees may result in (a) …
Noise Control in Buildings - 5 PDH
This course will introduce you to the basic principles and terminology of acoustics, and noise control engineering in buildings. You will learn about sound pressure levels, sound power levels, sound intensity levels, vibration levels, frequency, temporal …
Pavement Overlays - 3 PDH
Normally, overlays of existing pavements are used to increase the load-carrying capacity of an existing pavement or to correct a defective surface condition on the existing pavement. Of these reasons, the first requires a structural design procedure for …
Engineering Properties of Soil and Rock - 5 PDH
This course will introduce you to the engineering properties of soil and rock. You will learn how the properties of compaction, permeability, consolidation-swell, shear strength, stress-strain modulus (modulus of elasticity), and Poisson’s ratio are …
Fire Suppression ITM - 3 PDH
This course will introduce you to best practices for inspection, testing and maintenance of fire detection, alarm and suppression systems to assure reliable and effective operation in emergency situations. You will be introduced to the principles of …
Treatment Boiler Water - 5 PDH
This course provides an introduction to the treatment of steam boiler water to prevent buildup of harmful chemicals that can cause harmful corrosion, sludge buildup and other conditions that reduce the efficiency and service life of a boiler and its …
Small Flow Waste Treatment Systems - 3 PDH
This course will introduce you to small flow waste treatment systems such as septic tanks, waterless toilets, filtration and reuse systems, Imhoff tanks, and packaged treatment plants. You will learn about subsurface absorption and how to conduct …
Passive Solar Buildings - 3 PDH
This course is an introduction to passive solar technology to heat buildings. It will tell you about the basic passive systems and climate considerations you need to know about. You will gain knowledge about guidelines for schematic design of passive …
Water Distribution System Appurtenances - 3 PDH
This publication contains guidance for the operation and maintenance of various types of water distribution system appurtenances. Discussed are valves and hydrants; flow, pressure and level sensors; transmission systems; indicators, registers and …
Geotextiles in Pavement and Drainage Applications - 2 PDH
This course will introduce you to geotextiles made from polypropylene, polyester, polyethylene, polyamide (nylon), polyvinylidene chloride, and fiberglass. You will learn about their physical properties, functions, and design methods. You will also learn …
FHWA Bridge Inspection Fundamentals - 6 PDH
The Federal Highway Administration’s Bridge Inspector’s Reference Manual (BIRM) is a comprehensive manual on programs, procedures, and techniques for inspecting and evaluating a variety of in-service highway bridges. BIRM serves as the basis of a …
Asbestos Standard for the Construction Industry - 5 PDH
In the construction industry, asbestos is found in installed products such as sprayed-on fireproofing, pipe insulation, floor tiles, cement pipe and sheet, roofing felts and shingles, ceiling tiles, fire-resistant drywall, drywall joint compounds, and …
FHWA Bridge Inspection Reporting - 5 PDH
The Federal Highway Administration’s Bridge Inspector’s Reference Manual (BIRM) is a comprehensive manual on programs, procedures, and techniques for inspecting and evaluating a variety of in-service highway bridges. BIRM serves as the basis of a …
Methods for Cleaning Contaminated Soils - 4 PDH
EPA uses many methods to clean up pollution at Superfund and other sites. This course presents various EPA-approved methods for cleaning contaminated soils. For each method, the course describes 1) how the method works, 2) how safe it is, 3) how long it …
Building in Coastal Areas - 5 PDH
The design and construction of residential buildings in coastal zones presents problems not usually found in more inland locations. For example, all elements of the building must be able to withstand the large forces associated with high wind speeds and …
OSHA: Construction, Demolition & Cleanup Safety Issues - 6 PDH
Construction, demolition, and cleanup projects are inherently hazardous. Accident rates in these industries are accordingly higher than in other industries. OSHA’s mission is to reduce these accident rates through safety rules and regulations. This course …
Ethics in Professional Practice - 2 PDH
Many engineering organizations have drafted codes of ethics to which their members are required to commit. Generally, these codes are quite similar and are based on a few fundamental principles which provide guidance to professional engineers in common …
Engineering Ethics Case Study: The Challenger Disaster - 3 PDH
This course provides instruction in engineering ethics through a case study of the Space Shuttle Challenger disaster. The course begins by presenting the minimum technical details needed to understand the physical cause of the Shuttle failure. The …
OSHA: Fatalities from Improper Work Practices - 4 PDH
This course is based on case studies taken from the Occupational Safety and Health Administration’s “Fatal Facts” —descriptions of accidents in which one or more workers died because of improper work practices. Reading and thinking about these case …
Ethics, Professionalism, and Disciplinary Actions: 1 PDH
The ten case studies given below are taken from actual disciplinary-action documents of a state licensing board for professional engineers and other related professionals. Even though the cases come from a single state board, they are intended to be …
Course 1 Liquefied Natural Gas Introductory Course 2.5 PDH
Texas Compliance Pending. This course is the first in a series of Liquefied Natural Gas (LNG) Courses. This course is designed for engineers entering the specialty of LNG or who want to understand the basics of LNG …
Course 2 What Every Energy Engineer Needs to Know About Liquefied Natural Gas Safety 4.5 PDH
Texas Compliance Pending. This training covers LNG safety technologies at both a technical and human resource development level. This training is needed to help you design, operate or maintain an LNG facility; however, many …