All Courses
Electrical Safety Underground - 3 PDH
This course provides electrical safety guidance when working with underground electrical systems and low voltage interior systems. It applies to underground work in manholes, vaults, and handholes; work on duct lines, trenches, and underground cables; …
Hospital Water Systems - 3 PDH
This course will introduce you to design and construction considerations for domestic water supply systems for hospitals and other health care facilities.
High Temperature Water Heating Plants - 5 PDH
This course will introduce you to systems, equipment and design guidelines for high temperature water (HTW) heating plants. HTW systems are used for heating multi-building facilities such as campuses and industrial and commercial activities. The advantage …
Bearing Capacity Analysis - 3 PDH
This course will introduce you to methods for analysis of soils and rock to determine load bearing capacity. Stresses transmitted by a foundation to underlying soils must not cause bearing-capacity failure or excessive foundation settlement. The design …
Electrical Systems for Medical Facilities - 5 PDH
This course will introduce you to electrical systems for medical facilities, including hospitals, medical and dental clinics, and medical and dental laboratories. You will learn about general electrical requirements, exterior electrical systems, alternate …
Theatres Vol. 1 - 5 PDH
This publication provides an introduction to certain aspects of the architectural design of theatres and concert halls. Topics discussed include room characteristics, drama and music room qualities, house, stage, and primary and secondary uses. This …
Sharp-Crested Weirs: Open Channel Flow Measurement - 2 PDH
A weir is basically an obstruction in an open channel flow path. Weirs are commonly used for measurement of open channel flow rate. A weir functions by causing water to rise above the obstruction in order to flow over it. The height of water above the …
Interior Electrical Distribution Systems - 3 PDH
This publication provides an introduction to interior electrical distribution systems for buildings and related infrastructure. Topics covered include transformers, service entrances, switchgear, switchboards, panelboards, motor controls and motor …
Tropical Engineering: Mechanical, Electrical, Miscellaneous - 3 PDH
This course provides an introduction to special considerations in design of plumbing, HVAC, electrical distribution and miscellaneous features and systems in tropical climates where high humidity, heat, heavy rain and seafront conditions are common.
Flow Measurements in Pipes and Ducts - 3 PDH
This course is about measurement of the flow rate of a fluid flowing under pressure in a closed conduit. The closed conduit is often circular, but also may be square or rectangular (such as a heating duct) or any other shape. The other major category of …
Cathodic Protection Maintenance - 3 PDH
This course will provide you with an introduction to the methods, equipment and practices for inspection and maintenance of cathodic protection systems. Both galvanic (sacrificial anode) and impressed current systems are discussed.
Course 1 Liquefied Natural Gas Introductory Course 2.5 PDH
Texas Compliance Pending. This course is the first in a series of Liquefied Natural Gas (LNG) Courses. This course is designed for engineers entering the specialty of LNG or who want to understand the basics of LNG …
Hydroelectric Power Plant Structures - 3 PDH
The course discusses location, configuration and design considerations for hydroelectric powerhouses. The factors affecting the location include: Location of the spillway (when powerhouse is located adjacent to the dam). Location of navigation locks (on …
Water Treatment - 5 PDH
This course will provide an introduction to water treatment processes and technology. You will be introduced to factors to consider in selecting water treatment processes, preliminary treatment, aeration, coagulation and flocculation, sedimentation …
Retaining Walls And Excavation Support Systems - 3 PDH
Retaining walls must be designed so that foundation pressures do not exceed allowable bearing pressures, wall settlements are tolerable, safety factors against sliding and overturning are adequate, and the wall possesses adequate structural strength. …
Cathodic Protection for Underground Structures - 5 PDH
This is an introduction to cathodic protection for underground structures such as tanks and pipelines. It covers the two principal methods used to mitigate corrosion: the sacrificial anode and impressed current systems. It introduces you to the nine …
Petroleum Atmospheric Tanks - 5 PDH
This course provides guidance for the design of atmospheric storage tanks for storage of petroleum fuels. Underground and aboveground tanks in both horizontal and vertical configuration are discussed.
Preliminary Wastewater Treatment - 3 PDH
This course will introduce you to processes and equipment for preliminary treatment of wastewater. You will be introduced to descriptions, functions and design considerations for bar screens, comminuting devices, grit chambers, proportional weirs, …
HVAC Systems for Medical Facilities - 5 PDH
This course will introduce you to heating, ventilating and air conditioning (HVAC) systems for medical facilities such as hospitals and clinics. You will learn about air conditioning requirements, systems, equipment and design practices for the various …
Drainage Pipe Strength, Cover, and Bedding - 3 PDH
This course provides an introduction to drainage pipe strength, cover and bedding. A drainage pipe is defined as a structure (other than a bridge) to convey water through a trench or under a fill or some other obstruction. Materials for permanent-type …
Ethics in Professional Practice - 2 PDH
Many engineering organizations have drafted codes of ethics to which their members are required to commit. Generally, these codes are quite similar and are based on a few fundamental principles which provide guidance to professional engineers in common …
Implementing Design-Build in the Public Sector - 5 PDH
Public works project managers are under great pressure to award construction contracts using a loosely defined process called “design-build.” There are benefits that can be realized using design-build as a construction delivery process, but there are …
Auxiliary Power Systems Switchboard - 3 PDH
This publication provides technical guidance and design requirements for operation and maintenance of auxiliary electric power systems.
Solar Cooling Systems - 3 PDH
This course will introduce you to solar-powered cooling systems for buildings. You will learn about absorption cooling systems, Rankine cycle heat engine cooling systems, desiccant cooling, and other solar-powered systems having potential for commercial …
Design of Solar Water Heating Systems - 3 PDH
This course presents the information required to design a solar energy water heating system, after planning and system selection have been completed.
Area Development Plans - 3 PDH
Area Development Planning PDH provides an introduction to the Area Development Planning (ADP) process that is commonly used in developing new project sites. The planning procedures described are a guide that can be modified to suit specific project …
Architectural Theatres Vol. 3 - 3 PDH
This publication provides an introduction to certain aspects of the architectural design of theatres and concert halls. This volume discusses access, environmental systems, and performance support spaces.. Topics discussed include audience access, …
Energy Efficient HVAC Controls - 3 PDH
This course covers automatic temperature and humidity controls, space pressurization controls, safety controls, and energy monitoring and central supervisory control systems for heating, ventilating and air conditioning (HVAC) systems. The control system …
Area Drainage Systems - 5 PDH
This course will introduce you to normal requirements for design of surface and subsurface drainage systems for residential, commercial, institutional and industrial areas.
Heating and Cooling of Agitated Liquid Batches - 3 PDH
The course developed the derivation of the heating and cooling application equations, along with simplifying assumptions. Two examples were given: heating in a jacketed agitated vessel, and cooling with a submerged coil in an agitated tank. The physical …
Concrete Pavements - 7 PDH
This course provides information on the materials and construction procedures for portland cement concrete pavements. It describes the constituents to be used in concrete, the procedures to be used in manufacturing concrete, and the equipment and …
Engineering Ethics Case Study: The Challenger Disaster - 3 PDH
This course provides instruction in engineering ethics through a case study of the Space Shuttle Challenger disaster. The course begins by presenting the minimum technical details needed to understand the physical cause of the Shuttle failure. The …
Theatres Vol. 2 - 3 PDH
This publication provides an introduction to certain aspects of the architectural design of theatres and concert halls. This volume discusses accessory equipment. Topics discussed include general considerations, classification of accessory facilities, …
Sludge Handling, Treatment and Disposal - 5 PDH
This course will introduce you to processes and equipment for handling, treating and disposing of sludge produced by wastewater treatment plants. You will learn about sludge pumping, thickening, conditioning, dewatering, digestion, storage and final …
OSHA: Fatalities from Improper Work Practices - 4 PDH
This course is based on case studies taken from the Occupational Safety and Health Administration’s “Fatal Facts” —descriptions of accidents in which one or more workers died because of improper work practices. Reading and thinking about these case …
Water Supply Systems Operation and Maintenance - 3 PDH
This publication provides an introduction to maintenance inspections and general maintenance services required at domestic water supply systems. It contains information about tools and equipment, lubricants, and materials and supplies required to perform …
Fuel Cells Green Power - 3 PDH
Fuel cells are not just laboratory curiosities. While there is much work that needs to be done to optimize the fuel cell system (remember, the gasoline internal combustion engine is nearly 120 years old and still being improved), hydrogen fuel cell …
Cathodic Protection Principles - 5 PDH
This course will provide you with an introduction to the principles of cathodic protection for underground and underwater structures. You will be introduced to the physics and chemistry of the corrosion process and how to mitigate the corrosion using …
Course 2 What Every Energy Engineer Needs to Know About Liquefied Natural Gas Safety 4.5 PDH
Texas Compliance Pending. This training covers LNG safety technologies at both a technical and human resource development level. This training is needed to help you design, operate or maintain an LNG facility; however, many …
Carbon Adsorption for Waste Treatment - 3 PDH
This course discusses waste treatment using, primarily, activated carbon. Both liquid and vapor phase adsorption are discussed. Adsorption technologies may be applicable to treatment of both sanitary and industrial waste streams.
$99 Unlimited PDH Subscription (1 Year)
Take all the courses you need with our $99 Unlimited PDH Subscription! 365 Days access to all of our PDH courses allows you to to do as little or as much PDH Credit as you choose!
Seepage and Drainage - 7 PDH
This course covers surface erosion, and analysis of flow quantity and groundwater pressures associated with underseepage. Requirements are given for methods of drainage and pressure relief. Control of soil erosion must be considered in all new …
Communication Systems for Medical Facilities - 4 PDH
This course will introduce you to communication systems for medical facilities, including hospitals, medical clinics, and medical and laboratories. You will learn about communication distribution facilities, telephone system requirements, …
Petroleum Facilities General - 3 PDH
This course provides general information about petroleum products as a basis for the design of bulk fuel storage facilities, including bulk storage tanks and those components normally located within a typical bulk storage compound. These components …
Primary Wastewater Treatment - 3 PDH
Wastewater treatment is usually characterized as consisting of four sequential processes: preliminary, primary, secondary and tertiary treatment. This course will introduce you to processes and equipment for primary treatment of wastewater. You will be …
Activated Sludge Wastewater Treatment Plants - 3 PDH
This course provides an introduction to activated sludge wastewater treatment plants. In a conventional (plug-flow) activated sludge plant, the primary-treated wastewater and acclimated micro-organisms (activated sludge or biomass) are aerated in a basin …
Recycling Construction and Demolition Waste - 3 PDH
There is a significant amount of construction and demolition (C&D) waste developed due to construction activities and structure demolition, for example, at some installations, construction and demolition waste accounts for up to 80 percent of the solid …
Ethics, Professionalism, and Disciplinary Actions: 1 PDH
The ten case studies given below are taken from actual disciplinary-action documents of a state licensing board for professional engineers and other related professionals. Even though the cases come from a single state board, they are intended to be …