All Courses
Gas Distribution - 3 PDH
This course contains instructions and engineering information relating to gas distribution pipe systems, including pressure regulators, valves, meters, and other necessary appurtenances, for the distribution of fuel gas, natural and manufactured, from the …
Soil Grouting - 3 PDH
Grouting is a widely used method for strengthening and sealing rock, soil and concrete. The possibilities for sealing structures are of great importance from both an economic and environmental point of view. The cost of grouting has in certain projects …
Advanced Wastewater Treatment - 5 PDH
This course will introduce you to advanced wastewater treatment processes that provide higher quality wastewater discharge than achievable with primary and secondary treatment alone. You will learn innovative sewage handling techniques such as polishing …
Water System Pumps Operation and Maintenance - 3 PDH
This course covers the operation and maintenance of pumps used in water supply and treatment facilities. It also covers the motors, engines, and accessories (together called pump drivers) that provide the mechanical source of energy to pumps.
Heating and Cooling Distribution Systems - 3 PDH
This is an introduction to the design of heating and cooling distribution systems outside of buildings. It provides information about system selection, distribution media selection, and general distribution system design. Discussed are distribution …
Water Sampling Testing - 3 PDH
Water sampling and testing procedures provide information that can be used for the following purposes: to ensure the protection of the water system equipment; to prevent unexpected system failure; to provide information used to control water quality; and …
Asbestos Standard for the Construction Industry - 5 PDH
In the construction industry, asbestos is found in installed products such as sprayed-on fireproofing, pipe insulation, floor tiles, cement pipe and sheet, roofing felts and shingles, ceiling tiles, fire-resistant drywall, drywall joint compounds, and …
Solar Energy System Fundamentals - 3 PDH
This course provides an introduction to solar energy system fundamentals. A solar thermal energy collection system (or "solar system" for short) is defined as a set of equipment that intercepts incident solar radiation and stores it as useful thermal …
Domestic Wastewater Treatment - 3 PDH
This course will introduce you to the basics of domestic wastewater treatment. You will learn about preliminary measures, pretreatment, primary, secondary and advanced treatment processes, and sludge treatment and disposal. Approximate performance data …
Cooling Tower Water Treatment - 3 PDH
Cooling water systems remove heat generated from a variety of industrial processes. There are three basic types of cooling water systems: once-through, open recirculating, and closed recirculating cooling water systems. This publication describes water …
Course 4 LNG Thermodynamics Part 2 4 PDH
Texas Compliance Pending. This Part 2 course introduces the learner to the use of thermodynamic software in lieu of using charts for performing thermodynamic analyses. The use of such software is much more time efficient, …
Dam Arch Foundation Investigation - 3 PDH
Foundation investigations for arch dams generally must be accomplished in more exacting detail than for other dam types because of the critical relationship of the dam to its foundation and to its abutments. This course discusses the procedures which are …
Roofing Systems - 5 PDH
This is an introduction to roofing systems. You will learn how to specify roofing systems and incorporate appropriate engineering details into your working drawings on a wide variety of projects. You will learn about the different types of roofing systems …
Distribution of Stresses in Soil - 3 PDH
This course covers the analysis of stress conditions at a point, stresses beneath structures and embankments, and empirical methods for estimating loads on buried pipes, conduits, shafts, and tunnels.
Trickling Filter Wastewater Treatment Plants - 3 PDH
This course provides an introduction to trickling filter wastewater treatment plants. Trickling filter plants have been justified by their low initial cost, low operating and maintenance costs, and relative simplicity of operation. Although the effluent …
FHWA Bridge Inspection Reporting - 5 PDH
The Federal Highway Administration’s Bridge Inspector’s Reference Manual (BIRM) is a comprehensive manual on programs, procedures, and techniques for inspecting and evaluating a variety of in-service highway bridges. BIRM serves as the basis of a …
Sacrificial Anode Cathodic - 3 PDH
This course will provide you with an introduction to the methods, equipment and practices for design and operation of sacrificial anode cathodic protection systems.
Uniform Open Channel Flow and The Manning Equation -2 PDH
Flow of a liquid may take place either as open channel flow or pressure flow. Pressure flow takes place in a closed conduit such as a pipe, and pressure is the primary driving force for the flow. For open channel flow, on the other hand the flowing liquid …
Foundations In Areas of Significant Frost Penetration - 3 PDH
Areas of significant frost penetration may be defined as those in which freezing temperatures occur in the ground to sufficient depth to be a significant factor in foundation design. These areas may be further characterized as seasonal frost and …
Boiler Control Systems: An Introduction - 4 PDH
This course provides an introduction to criteria for the design of heating plant instrumentation. A heating plant may contain one or more boilers. The plant may be an individual plant serving a single building or a compact group of buildings, or a …
Bulk Fuel Storage - 5 PDH
This course provides guidance for the design of bulk fuel storage facilities, including bulk storage tanks and those components normally located within a typical bulk storage compound. These components include pipeline receiving facilities, tank truck and …
Laboratory Testing of Soils - 5 PDH
This course will introduce you to the principles and practices of laboratory testing of soils. You will learn about index property, permeability, consolidation, and shear strength tests. You will be introduced to dynamic testing methods, and tests on …
Geometrics for Roads and Streets - 3 PDH
This courses discusses the geometric design criteria for roads and streets. It sets forth the approaches and traffic flow criteria for guidance in determining types and configurations best suited for construction.
Water Cooling Towers - 3 PDH
Cooling water systems remove heat generated from a variety of industrial processes. There are three basic types of cooling water systems: once-through, open recirculating, and closed recirculating cooling water systems. This course describes once-through …
Methods for Cleaning Contaminated Soils - 4 PDH
EPA uses many methods to clean up pollution at Superfund and other sites. This course presents various EPA-approved methods for cleaning contaminated soils. For each method, the course describes 1) how the method works, 2) how safe it is, 3) how long it …
Slope Stability Analysis - 3 PDH
This course is concerned with characteristics and critical aspects of the stability of excavation slopes; methods of designing slopes, including field observations and experience, slope stability charts, and detailed analyses; factors of safety; and …
Ethical Issues from the St. Francis Dam Failure - 3 PDH
This course will examine the ethical issues that arose from the 1928 failure of the St. Francis Dam near Los Angeles, California. Near midnight on March 12 of that year the 195-feet high concrete arch dam collapsed catastrophically, releasing 12 billion …
Impressed Current Cathodic - 3 PDH
This course provides an introduction to impressed current cathodic protection systems. There are two principle methods of providing cathodic protection: sacrificial anode and impressed current. The primary advantage of impressed current cathodic …
Soil Stabilization for Pavements - 3 PDH
This course will introduce you to accepted methods for stabilizing soils underlying new pavements to improve strength and durability. You will also learn about methods to achieve better soil gradation, and reduction of plasticity index or swelling …
An Engineer’s Guide to Influencing Public Policy - 3 PDH
Engineers often are called upon to interact with public policy makers in the course of their careers, their professional development, and in pursuit of personal interests. There are, however, fundamental differences in what motivates engineers and what …
400 Hz Electrical - 3 PDH
This course includes information necessary for the proper design of 400-Hertz (Hz) conversion, distribution, and utilization systems. Special regard is paid to systems utilizing medium-voltage distribution. Systems supplying 400 Hz for ground-power …
How To Become Registered as an Architectural Engineer - 3 PDH
Engineers who have passed the Fundamentals of Engineering (FE) registration examination (formerly called the Engineer-in-Training….EIT exam) or both the FE and the Principles and Practices of Engineering (PE) registration examination in another discipline …
Landfill Gas Systems - 3 PDH
This course discusses the need for an operation and maintenance (O&M) plan for a landfill gas collection system that addresses the following: extraction wells; LFG monitoring probes; condensate collection and treatment; and flare station. A site-specific …
Chemical Cleaning and Industrial Water Systems - 2 PDH
This course will introduce you to methods for cleaning industrial water systems with chemicals. You will learn about pre-operational cleaning which is performed to prepare water-contacted metal surfaces to receive chemical treatment to provide protection …
Steam Generators - 3 PDH
This course addresses the design requirements for gas, oil, coal, and waste fuel fired steam generating, water-tube boilers and components with steam capacities between 20,000 and 250,000 pph and maximum pressures of 450 pounds per inch gauge …
Domestic Wastewater Treatment: EPA Overview - 3 PDH
The 1972 legislation known as the Clean Water Act set secondary treatment as the required level of treatment to be provided by domestic wastewater treatment plants in the United States. In this course you can learn about the basic processes used in …
Electrical Safety Aerial - 3 PDH
This course includes specific requirements for poles and structures, pole-mounted equipment, and aerial lines. Requirements addressed include pole handling and erection, climbing and working on poles, stringing of lines, working around pole-mounted …
Course 5 LNG Thermodynamics Part 3A 2 PDH
Texas Compliance Pending. This course introduces learners to Liquefied Natural Gas (LNG) production processes. LNG is widely used around the world. It is a very compact form of natural gas in liquid form. It is used on very …
Adsorption Technologies Operation Theory- 3 PDH
This course discusses practical guidance for the design of liquid and vapor phase devices for the adsorption of organic chemicals. The adsorptive media addressed include granular activated carbon (GAC) and other alternative adsorption carbon media, such …
Sanitary Landfills - 3 PDH
This is an introduction to the planning and design of sanitary landfills. You will learn about dry and wet landfills, site selection, site development plans, site layout, trench design, leachate control and treatment, gas control, runoff control, support …
Hydraulic Design of Culverts - 3 PDH
This course will introduce you to a nomographic approach to hydraulic design of culverts. Culverts are hydraulic structures intended to convey, generally, stormwater and other unanticipated flows in and around earth and other structures such as highways, …
Tropical Engineering: Building Envelope - 3 PDH
This publication provides an introduction to design of building envelopes in tropical climates where heat and humidity are important considerations. Discussed are roofing, wall materials, windows, doors, finishes and miscellaneous specialties.
Fire Protection Engineering for Buildings - 3 PDH
This course will introduce you to fire protection engineering fundamentals related to building materials and design, water supply for fire protection, fire extinguishing systems, fire alarm systems, special occupancies and hazards, and storage of …
Security Fences - 3 PDH
This course applies to all construction, renovation, and repair projects including temporary construction that includes security fencing and gates. Security fences and gates are installed and used primarily to define the perimeter of protected areas, such …
Valve Fundamentals - 4 PDH
Valves are widely used in fluid piping systems to shut off or throttle flow, as well as to prevent backflow, reduce pressure or relieve pressure. This course provides information about the basic components of a valve and their function. There is also …
Pavement Design in Seasonal Frost Conditions - 5 PDH
This publication presents criteria and procedures for the design and construction of pavements placed on subgrade or base course materials subject to seasonal frost action. The most prevalent modes of distress in pavements and their causes are listed. The …
Building Design Specifications and Tools - 3 PDH
This course will introduce you to the most important resource available to engineers and architects engaged in the design of buildings and related infrastructure. It represents the collective knowledge of thousands of engineers and architects acquired …
Cathodic Concepts - 3 PDH
This course provides the basic concepts of cathodic protection, together with important criteria and precautions to be observed. Corrosion of metals is a result of electrochemical reactions. An electrochemical reaction is a chemical reaction accompanied …