All Courses
Integrating Climate Change Data into Codes and Standards - 3.5 PDH
The goal of this course is to equip building professionals with the knowledge to anticipate and incorporate future climate risks into today’s building standards.
Roofing Systems - 5 PDH
This is an introduction to roofing systems. You will learn how to specify roofing systems and incorporate appropriate engineering details into your working drawings on a wide variety of projects. You will learn about the different types of roofing systems …
Distribution of Stresses in Soil - 3 PDH
This course covers the analysis of stress conditions at a point, stresses beneath structures and embankments, and empirical methods for estimating loads on buried pipes, conduits, shafts, and tunnels.
Trickling Filter Wastewater Treatment Plants - 3 PDH
This course provides an introduction to trickling filter wastewater treatment plants. Trickling filter plants have been justified by their low initial cost, low operating and maintenance costs, and relative simplicity of operation. Although the effluent …
Bulk Fuel Storage - 5 PDH
This course provides guidance for the design of bulk fuel storage facilities, including bulk storage tanks and those components normally located within a typical bulk storage compound. These components include pipeline receiving facilities, tank truck and …
Laboratory Testing of Soils - 5 PDH
This course will introduce you to the principles and practices of laboratory testing of soils. You will learn about index property, permeability, consolidation, and shear strength tests. You will be introduced to dynamic testing methods, and tests on …
Geometrics for Roads and Streets - 3 PDH
This courses discusses the geometric design criteria for roads and streets. It sets forth the approaches and traffic flow criteria for guidance in determining types and configurations best suited for construction.
Uniform Open Channel Flow and The Manning Equation -2 PDH
Flow of a liquid may take place either as open channel flow or pressure flow. Pressure flow takes place in a closed conduit such as a pipe, and pressure is the primary driving force for the flow. For open channel flow, on the other hand the flowing liquid …
Foundations In Areas of Significant Frost Penetration - 3 PDH
Areas of significant frost penetration may be defined as those in which freezing temperatures occur in the ground to sufficient depth to be a significant factor in foundation design. These areas may be further characterized as seasonal frost and …
Boiler Control Systems: An Introduction - 4 PDH
This course provides an introduction to criteria for the design of heating plant instrumentation. A heating plant may contain one or more boilers. The plant may be an individual plant serving a single building or a compact group of buildings, or a …
Ethical Issues from the St. Francis Dam Failure - 3 PDH
This course will examine the ethical issues that arose from the 1928 failure of the St. Francis Dam near Los Angeles, California. Near midnight on March 12 of that year the 195-feet high concrete arch dam collapsed catastrophically, releasing 12 billion …
Impressed Current Cathodic - 3 PDH
This course provides an introduction to impressed current cathodic protection systems. There are two principle methods of providing cathodic protection: sacrificial anode and impressed current. The primary advantage of impressed current cathodic …
Designing Fire & EMS Stations A Comprehensive Guide - 11 PDH
This course dives into the critical aspects of designing fire and EMS stations that prioritize safety, health, and operational efficiency. From station layout and site selection to ensuring compliance with regulatory standards.
Water Cooling Towers - 3 PDH
Cooling water systems remove heat generated from a variety of industrial processes. There are three basic types of cooling water systems: once-through, open recirculating, and closed recirculating cooling water systems. This course describes once-through …
Methods for Cleaning Contaminated Soils - 4 PDH
EPA uses many methods to clean up pollution at Superfund and other sites. This course presents various EPA-approved methods for cleaning contaminated soils. For each method, the course describes 1) how the method works, 2) how safe it is, 3) how long it …
Slope Stability Analysis - 3 PDH
This course is concerned with characteristics and critical aspects of the stability of excavation slopes; methods of designing slopes, including field observations and experience, slope stability charts, and detailed analyses; factors of safety; and …
400 Hz Electrical - 3 PDH
This course includes information necessary for the proper design of 400-Hertz (Hz) conversion, distribution, and utilization systems. Special regard is paid to systems utilizing medium-voltage distribution. Systems supplying 400 Hz for ground-power …
How To Become Registered as an Architectural Engineer - 3 PDH
Engineers who have passed the Fundamentals of Engineering (FE) registration examination (formerly called the Engineer-in-Training….EIT exam) or both the FE and the Principles and Practices of Engineering (PE) registration examination in another discipline …
Landfill Gas Systems - 3 PDH
This course discusses the need for an operation and maintenance (O&M) plan for a landfill gas collection system that addresses the following: extraction wells; LFG monitoring probes; condensate collection and treatment; and flare station. A site-specific …
Bioretention Design: Performance, Longevity, and Sustainability - 10 PDH
Stormwater management is evolving, and bioretention systems are at the forefront of sustainable infrastructure. This course introduces the principles of bioretention, guiding participants through design elements, engineering strategies, and best practices …