Design/Build
Dam Arch Construction - 3 PDH
This course will introduce you to the construction of concrete arch dams. The design and analysis of any dam assumes that the construction will provide a suitable foundation and uniform quality of concrete. The design also depends on the construction to …
Cooling Tower Water Treatment - 3 PDH
Cooling water systems remove heat generated from a variety of industrial processes. There are three basic types of cooling water systems: once-through, open recirculating, and closed recirculating cooling water systems. This publication describes water …
Passive Solar Buildings - 3 PDH
This course is an introduction to passive solar technology to heat buildings. It will tell you about the basic passive systems and climate considerations you need to know about. You will gain knowledge about guidelines for schematic design of passive …
Deep Foundations - 3 PDH
This course will provide you with an introduction to deep foundations. A deep foundation derives its support from competent strata at significant depths below the surface or, alternatively, has a depth to diameter ratio greater than 4. A deep foundation …
Theatres Vol. 2 - 3 PDH
This publication provides an introduction to certain aspects of the architectural design of theatres and concert halls. This volume discusses accessory equipment. Topics discussed include general considerations, classification of accessory facilities, …
Pavement Overlays - 3 PDH
Normally, overlays of existing pavements are used to increase the load-carrying capacity of an existing pavement or to correct a defective surface condition on the existing pavement. Of these reasons, the first requires a structural design procedure for …
Architectural Theatres Vol. 4 - 3 PDH
This publication provides an introduction to certain aspects of the architectural design of theatres and concert halls. This volume discusses theatre lighting, scenery and soft goods, and rigging and stage mechanisms. Topics discussed include audience …
Petroleum Facilities General - 3 PDH
This course provides general information about petroleum products as a basis for the design of bulk fuel storage facilities, including bulk storage tanks and those components normally located within a typical bulk storage compound. These components …
Retaining Walls And Excavation Support Systems - 3 PDH
Retaining walls must be designed so that foundation pressures do not exceed allowable bearing pressures, wall settlements are tolerable, safety factors against sliding and overturning are adequate, and the wall possesses adequate structural strength. …
Tropical Engineering: Building Envelope - 3 PDH
This publication provides an introduction to design of building envelopes in tropical climates where heat and humidity are important considerations. Discussed are roofing, wall materials, windows, doors, finishes and miscellaneous specialties.
Waste Treatment Carbon Adsorption Applications - 3 PDH
This course discusses waste treatment using, primarily, activated carbon. Both liquid and vapor phase adsorption are discussed. Adsorption technologies may be applicable to treatment of both sanitary and industrial waste streams.
Energy Efficient HVAC Controls - 3 PDH
This course covers automatic temperature and humidity controls, space pressurization controls, safety controls, and energy monitoring and central supervisory control systems for heating, ventilating and air conditioning (HVAC) systems. The control system …
Ethical Issues in Design-Build - 3 PDH
The widespread growth of “design-build” presents ethical issues for engineers and architects. If these issues are not addressed it is likely public reaction to abuses the process invites will result in the loss of design-build as a construction delivery …
Design of Solar Water Heating Systems - 3 PDH
This course presents the information required to design a solar energy water heating system, after planning and system selection have been completed.
Water Sampling Testing - 3 PDH
Water sampling and testing procedures provide information that can be used for the following purposes: to ensure the protection of the water system equipment; to prevent unexpected system failure; to provide information used to control water quality; and …
Roller-Compacted Concrete Pavements - 3 PDH
Procedures and criteria described here are applicable to the design and construction of roller-compacted concrete (RCC) pavement (RCCP). Roller-compacted concrete pavement employs a concrete paving technology that involves laydown and compaction of a …
Cathodic Concepts - 3 PDH
This course provides the basic concepts of cathodic protection, together with important criteria and precautions to be observed. Corrosion of metals is a result of electrochemical reactions. An electrochemical reaction is a chemical reaction accompanied …
Distribution of Stresses in Soil - 3 PDH
This course covers the analysis of stress conditions at a point, stresses beneath structures and embankments, and empirical methods for estimating loads on buried pipes, conduits, shafts, and tunnels.
Petroleum Pipelines - 3 PDH
This discussion provides guidance for the design of pipelines. Pipelines are typically either interterminal pipelines which are cross country and connect installations, or installation pipelines which connect petroleum-oil-lubricants (POL) facilities …
Settlement and Volume Expansion in Soils -5 PDH
This course concerns (a) immediate settlements, (b) long-term settlements, (c) rate of settlement, (d) criteria for tolerable settlement, (e) methods of reducing or accelerating settlements for saturated fine-grained soils and (f) methods for controlling …
OSHA: Construction, Demolition & Cleanup Safety Issues - 6 PDH
Construction, demolition, and cleanup projects are inherently hazardous. Accident rates in these industries are accordingly higher than in other industries. OSHA’s mission is to reduce these accident rates through safety rules and regulations. This course …
OSHA: Fatalities from Improper Work Practices - 4 PDH
This course is based on case studies taken from the Occupational Safety and Health Administration’s “Fatal Facts” —descriptions of accidents in which one or more workers died because of improper work practices. Reading and thinking about these case …
Earthquake Resilience Benefit-Cost Analysis for Building Design and Retrofit - 2 PDH
This course is ideal for engineers, architects, building owners, policymakers, and disaster preparedness professionals interested in improving the earthquake resilience of buildings.
Effects of Weathering on the Properties of Vinyl Siding - 4 PDH
This course equips building professionals with the knowledge to optimize the longevity and safety of exterior building materials.
Design Standards for Federal Public Buildings - 20 PDH
This course introduces participants to its core principles, equipping them with the knowledge to navigate complex standards, implement innovative solutions, and achieve excellence in every project phase.
America Burning Design Strategies for Fire Prevention - 15 PDH
This course empowers professionals to integrate prevention design strategies, enhance public awareness, and adopt innovative practices for reducing fire incidents and losses.
Assessment of Design Criteria and Best Practices for a Resilient Tomorrow - 15 PDH
This course provides a comprehensive exploration of the design criteria and best practices essential for improving community resilience in the face of natural hazards.
Designing Fire & EMS Stations A Comprehensive Guide - 11 PDH
This course dives into the critical aspects of designing fire and EMS stations that prioritize safety, health, and operational efficiency. From station layout and site selection to ensuring compliance with regulatory standards.
A High Value Compilation of Safety Moments - 3.5 PDH
The course equips participants with the knowledge to identify potential risks, foster a culture of safety, and implement preventive measures to protect personnel, equipment, and the community.